Nissan Versa Note. Manual — part 154
CHG
DIAGNOSIS AND REPAIR WORKFLOW
CHG-17
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
NO
>> Repair as needed.
9.
INSPECTION WITH CHARGE WARNING LAMP (ENGINE AT 3,000 RPM)
Increase and maintain the engine speed at 3,000 rpm.
Does the charge warning lamp remain off?
YES
>> GO TO 11.
NO
>> GO TO 10.
10.
INSPECTION OF GENERATOR PULLEY
Check generator pulley. Refer to
CHG-29, "Removal and Installation"
Is generator pulley normal?
YES
>> Replace generator. Refer to
CHG-29, "Removal and Installation"
NO
>> Repair as needed.
11.
“B” TERMINAL CIRCUIT INSPECTION
Check “B” terminal circuit. Refer to
Is “B” terminal circuit normal?
YES
>> Replace generator. Refer to
CHG-29, "Removal and Installation"
NO
>> Repair as needed.
12.
“B” TERMINAL CIRCUIT INSPECTION
Check “B” terminal circuit. Refer to
Is “B” terminal circuit normal?
YES
>> GO TO 13.
NO
>> Repair as needed.
13.
INSPECTION OF GENERATOR PULLEY
Check generator pulley. Refer to
CHG-29, "Removal and Installation"
Is generator pulley normal?
YES
>> Replace generator. Refer to
CHG-29, "Removal and Installation"
NO
>> Repair as needed.
14.
“S” TERMINAL CIRCUIT INSPECTION
Check “S” terminal circuit. Refer to
Is the “S” terminal circuit normal?
YES
>> Replace generator. Refer to
CHG-29, "Removal and Installation"
NO
>> Repair as needed.
Work Flow (Without EXP-800 NI or GR8-1200 NI)
INFOID:0000000009682025
OVERALL SEQUENCE
Before performing a generator test, make sure that the battery is fully charged. A 30-volt voltmeter and suit-
able test probes are necessary for the test.
• Before starting, inspect the fusible link.
CHG-18
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
• Use fully charged battery.
DETAILED FLOW
1.
PRELIMINARY INSPECTION
Perform the preliminary inspection. Refer to
>> GO TO 2.
2.
STOP POWER GENERATION VOLTAGE VARIABLE CONTROL SYSTEM
Stop the operation of the power generation voltage variable control in either of the following procedures:
• After selecting “ENGINE” using CONSULT, set the DUTY value of “ALTERNATOR DUTY” to 0 % by select-
ing “ALTERNATOR DUTY” with “Active Test”. Continue “Active Test” until the end of inspection. (When the
DUTY value is 0 or 100 %, the normal power generation is performed according to the characteristic of the
IC regulator of the generator.)
• Turn the ignition switch OFF, and disconnect the battery current sensor connector. [However, DTC (P1550 -
P1554) of the engine might remain. After finishing the inspection, connect the battery current sensor connec-
tor and erase the self-diagnostic results history of the engine using CONSULT.]
>> GO TO 3.
3.
INSPECTION WITH CHARGE WARNING LAMP (IGNITION SWITCH IS TURNED ON)
When ignition switch is turned ON.
Does the charge warning lamp illuminate?
ALMIA0577GB
CHG
DIAGNOSIS AND REPAIR WORKFLOW
CHG-19
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
YES
>> GO TO 4.
NO
>> GO TO 10.
4.
INSPECTION WITH CHARGE WARNING LAMP (IDLING)
Start the engine and run it at idle
Does the charge warning lamp turn OFF?
YES
>> GO TO 5.
NO
>> GO TO 6.
5.
INSPECTION WITH CHARGE WARNING LAMP (ENGINE AT 2,500 RPM)
Increase and maintain the engine speed at 2,500 rpm.
Does the charge warning lamp illuminate?
YES
>> GO TO 8.
NO
>> Inspection End.
6.
“L” TERMINAL CIRCUIT (SHORT) INSPECTION
Check terminal “L” circuit for (short). Refer to
.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair as needed.
7.
“S” TERMINAL CIRCUIT INSPECTION
Check terminal “S” circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair as needed.
8.
MEASURE “B” TERMINAL VOLTAGE
Start engine. With engine running at 2,500 rpm, measure “B” terminal voltage.
What voltage does the measurement result show?
Less than 13.0 V>>GO TO 9.
More than 16.0 V>>Replace generator. Refer to
CHG-29, "Removal and Installation"
9.
“B” TERMINAL CIRCUIT INSPECTION
Check “B” terminal circuit. Refer to
Is the inspection result normal?
YES
>> Replace generator. Refer to
CHG-29, "Removal and Installation"
NO
>> Repair as needed.
10.
INSPECTION WITH CHARGE WARNING LAMP (IGNITION SWITCH IS ON)
1. Disconnect generator connector and apply ground to “L” terminal.
2. Turn the ignition switch ON.
Does the charge warning lamp illuminate?
YES
>> Replace generator. Refer to
CHG-29, "Removal and Installation"
.
NO
>> GO TO 11.
11.
CHECK “L” TERMINAL CIRCUIT (OPEN)
Check “L” terminal circuit (OPEN). Refer to
.
>> Repair as needed.
CHG-20
< DTC/CIRCUIT DIAGNOSIS >
CHARGING SYSTEM PRELIMINARY INSPECTION
DTC/CIRCUIT DIAGNOSIS
CHARGING SYSTEM PRELIMINARY INSPECTION
Diagnosis Procedure
INFOID:0000000009682026
1.
CHECK BATTERY TERMINALS CONNECTION
Check if battery terminals are clean and tight.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair battery terminal connection. Confirm repair by performing complete Charging system test
using EXP-800 NI or GR8-1200 NI (if available). Refer to the applicable Instruction Manual for
proper testing procedures.
2.
CHECK FUSE
Check for blown fuse and fusible link.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace the blown fuse or fusible link after repairing the affected circuit.
3.
CHECK GENERATOR GROUND TERMINAL CONNECTION
Check if connector F4 terminal 5 is clean.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair connection.
4.
CHECK DRIVE BELT TENSION
Check drive belt tension. Refer to
.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair as needed.
Unit
Power source (Power supply terminals)
Fuse or Fusible Link
Generator
Battery (terminal 3)
Fuse 24
Battery (terminal 1)
Fusible Link A
Combination meter
Ignition switch ON (terminal 2)
Fuse 3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст