Nissan Versa Note. Manual — part 764
COMPONENT PARTS
STC-5
< SYSTEM DESCRIPTION >
C
D
E
F
H
I
J
K
L
M
A
B
STC
N
O
P
EPS Control Unit
INFOID:0000000009667171
• EPS control unit (1) is installed to steering column assembly.
• EPS control unit performs an arithmetical operation on data, such
as steering wheel turning force (sensor signal) from the torque
sensor, vehicle speed signal, etc. Then it generates an optimum
assist torque signal to the EPS motor according to the driving con-
dition.
• EPS control unit decreases the output signal to EPS motor while
extremely using the power steering function (e.g., full steering)
consecutively for protecting EPS motor and EPS control unit
(Overload protection control).
EPS Motor, Torque Sensor, Reduction Gear
INFOID:0000000009667172
EPS motor (1), torque sensor (2) and reduction gear (3) are installed
to steering column assembly.
EPS MOTOR
EPS motor provides the assist torque by the control signal from EPS control unit.
TORQUE SENSOR
Torque sensor detects the steering torque, and transmits the signal to EPS control unit.
REDUCTION GEAR
Reduction gear increases the assist torque provided from EPS motor with worm gears, and outputs to the col-
umn shaft.
4.
EPS motor
Refer to
STC-5, "EPS Motor, Torque Sensor, Reduction
.
5.
Reduction gear
Refer to
STC-5, "EPS Motor, Torque Sensor, Reduction
.
6.
EPS control unit
Refer to
7.
Torque sensor
Refer to
STC-5, "EPS Motor, Torque Sensor, Reduction
.
No.
Component
Function
JSGIA0852ZZ
JSGIA0853ZZ
STC-6
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (EPS CONTROL UNIT)
DIAGNOSIS SYSTEM (EPS CONTROL UNIT)
CONSULT Function
INFOID:0000000009667173
FUNCTION
CONSULT can display each diagnostic item using the diagnostic test modes shown following.
*: The following diagnosis information is erased by erasing.
• DTC
• Freeze frame data (FFD)
ECU IDENTIFICATION
Displays the part number stored in the control unit.
SELF-DIAG RESULTS MODE
.
When “CRNT” is displayed on self-diagnosis result.
• The system is presently malfunctioning.
When “PAST” is displayed on self-diagnosis result.
• System malfunction in the past is detected, but the system is presently normal.
FREEZE FRAME DATA (FFD)
The following vehicle status is recorded when DTC is detected and is displayed on CONSULT.
DATA MONITOR MODE
*1: Almost in accordance with the value of “MOTOR SIG”. It is not a malfunction though these values are not
accorded when steering quickly.
Diagnostic test mode
Function
ECU identification
The part number stored in the control unit can be read.
Self diagnostic result
Self-diagnostic results and freeze frame data can be read and erased quickly.
*
Data monitor
Input/Output data in the EPS control unit can be read.
Item name
Display item
IGN COUNTER
(0-39)
The number of times that ignition switch is turned ON after the DTC is detected is displayed.
• When “0” is displayed: It indicates that the system is presently malfunctioning.
• When except “0” is displayed: It indicates that system malfunction in the past is detected, but the system is pres-
ently normal.
NOTE:
Each time when ignition switch is turned OFF to ON, numerical number increases in 1
→2→3...38→39.
When the operation number of times exceeds 39, the number does not increase and “39” is displayed until self-
diagnosis is erased.
Monitor item (Unit)
Remarks
BATTERY VOLT (V)
Displays the power supply voltage for EPS control unit.
TORQUE SENSOR (Nm)
Displays steering wheel turning force detected by torque sensor.
MOTOR CURRENT (A)
Displays the current value consumed by EPS motor.
*1
MOTOR SIG (A)
Displays the current commanded value to EPS motor.
ASSIST TORQUE (Nm)
Displays assist torque being output by the electric power steering.
C/U TEMP (
°C or °F )
Displays the temperature of the EPS control unit.
ASSIST LEVEL (%)
Normally displays 100%. In case of an excessive stationary steering, the assist
curvature gradually falls. However, it return to 100% when left standing.
*2
VEHICLE SPEED (km/h or MPH)
Vehicle speed is displayed from vehicle speed signal via CAN communication.
*3
WARNING LAMP (On/Off)
EPS warning lamp control status is displayed.
ENGINE STATUS (Stop/Run)
Engine speed is displayed from engine status signal via CAN communication.
DIAGNOSIS SYSTEM (EPS CONTROL UNIT)
STC-7
< SYSTEM DESCRIPTION >
C
D
E
F
H
I
J
K
L
M
A
B
STC
N
O
P
*2: Normally displays 100%. In case of an excessive stationary steering, the assist curvature gradually falls.
However, it returns to 100% when left standing.
*3: It is not a malfunction, though it might not be corresponding just after ignition switch in turned ON.
STC-8
< ECU DIAGNOSIS INFORMATION >
EPS CONTROL UNIT
ECU DIAGNOSIS INFORMATION
EPS CONTROL UNIT
Reference Value
INFOID:0000000009667174
VALUES ON THE DIAGNOSIS TOOL
CAUTION:
The output signal indicates the EPS control unit calculation data. The normal values will be displayed
even in the event that the output circuit (harness) is open.
*1: Almost in accordance with the value of “MOTOR SIG”. It is not a malfunction though these values are not
accorded when steering quickly.
*2: A fixed value is indicated regardless of steering turning.
*3: Normally displays 100%. In case of an excessive stationary steering, the assist curvature gradually falls.
However, it returns to 100% when left standing.
*4: It is not a malfunction, though it might not be corresponding just after ignition switch in turned ON.
Monitor item
Data monitor
Condition
Display value
BATTERY VOLT
Ignition switch: ON
Battery voltage
TORQUE SENSOR
Engine running
Steering wheel: Not steering (There is
no steering force)
Approx. 0 Nm
Steering wheel: Right turn
Positive value (Nm)
Steering wheel: Left turn
Negative value (Nm)
MOTOR CURRENT
Engine running
Steering wheel: Not steering (There is
no steering force)
Approx. 0 A
Steering wheel: Right or left turn
Displays consumption current of
EPS motor (A)
*1
MOTOR SIG
Engine running
Steering wheel: Not steering (There is
no steering force)
Approx. 0 A
Steering wheel: Right turn
Positive value (A)
Steering wheel: Left turn
Negative value (A)
ASSIST TORQUE
Engine running
Approx. 0 Nm
*2
C/U TEMP
Ignition switch ON or engine running
Displays temperature of inside of
EPS control unit (
°C or °F)
ASSIST LEVEL
Engine running
100 %
*3
VEHICLE SPEED
Vehicle stopped
0 km/h or mph
While driving
Approximately equal to the indication
on speedometer
*4
(inside of
±10%)
WARNING LAMP
EPS warning lamp: ON
On
EPS warning lamp: OFF
Off
ENGINE STATUS
Engine not running
Stop
Engine running
Run
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст