Nissan Versa Note. Manual — part 122
BRC-52
< BASIC INSPECTION >
[VDC/TCS/ABS]
ADDITIONAL SERVICE WHEN REPLACING ABS ACTUATOR AND ELECTRIC
UNIT (CONTROL UNIT)
ADDITIONAL SERVICE WHEN REPLACING ABS ACTUATOR AND ELEC-
TRIC UNIT (CONTROL UNIT)
Description
INFOID:0000000009364903
After replacing the ABS actuator and electric unit (control unit), perform the neutral position adjustment for the
steering angle sensor. Refer to
.
Work Procedure
INFOID:0000000009364904
1.
PERFORM THE NEUTRAL POSITION ADJUSTMENT FOR THE STEERING ANGLE SENSOR
Perform the neutral position adjustment for the steering angle sensor.
>> Refer to
.
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
BRC-53
< BASIC INSPECTION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
Description
INFOID:0000000009364905
Refer to the table below to determine if adjustment of steering angle sensor neutral position is required.
×: Required –: Not required
Work Procedure
INFOID:0000000009364906
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
CAUTION:
To adjust neutral position of steering angle sensor, make sure to use CONSULT.
(Adjustment cannot be done without CONSULT).
1.
ALIGN THE VEHICLE STATUS
Stop vehicle with front wheels in straight-ahead position.
>> GO TO 2
2.
PERFORM THE NEUTRAL POSITION ADJUSTMENT FOR THE STEERING ANGLE SENSOR
1. On the CONSULT screen, touch “WORK SUPPORT” and “ST ANG SEN ADJUSTMENT” in order.
2. Touch “START”.
CAUTION:
Do not touch steering wheel while adjusting steering angle sensor.
3. After approximately 10 seconds, touch “END”.
NOTE:
After approximately 60 seconds, it ends automatically.
4. Turn ignition switch OFF, then turn it ON again.
CAUTION:
Be sure to perform above operation.
>> GO TO 3
3.
CHECK DATA MONITOR
1. Run vehicle with front wheels in straight-ahead position, then stop.
2. Select “DATA MONITOR”. Then make sure “STR ANGLE SIG” is within 0
±2.5°.
Is the steering angle within the specified range?
YES
>> GO TO 4
NO
>> Perform the neutral position adjustment for the steering angle sensor again, GO TO 1
4.
ERASE THE SELF-DIAGNOSIS MEMORY
Erase the self-diagnosis memory of the ABS actuator and electric unit (control unit) and ECM.
• ABS actuator and electric unit (control unit): Refer to
BRC-30, "CONSULT Function (ABS)"
Situation
Adjustment of steering angle sensor neutral position
Removing/Installing ABS actuator and electric unit (control unit)
—
Replacing ABS actuator and electric unit (control unit)
×
Removing/Installing steering angle sensor
×
Replacing steering angle sensor
×
Removing/Installing steering components
×
Replacing steering components
×
Removing/Installing suspension components
×
Replacing suspension components
×
Change tires to new ones
—
Tire rotation
—
Adjusting wheel alignment
×
BRC-54
< BASIC INSPECTION >
[VDC/TCS/ABS]
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
• ECM: Refer to
Are the memories erased?
YES
>> Inspection End
NO
>> Check the items indicated by the self-diagnosis.
C1101, C1102, C1103, C1104 WHEEL SENSOR
BRC-55
< DTC/CIRCUIT DIAGNOSIS >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
DTC/CIRCUIT DIAGNOSIS
C1101, C1102, C1103, C1104 WHEEL SENSOR
DTC Logic
INFOID:0000000009641656
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAGNOSTIC RESULT
With
CONSULT.
1. Start engine and drive vehicle at approximately 21 km/h (13 MPH) or more for approximately 5 minutes.
2. Perform self-diagnostic result.
Is DTC C1101, C1102, C1103 or C1104 detected?
YES
>> Proceed to diagnosis procedure. Refer to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009641657
Regarding Wiring Diagram information, refer to
1.
CONFIRM DTC
With CONSULT
1. Perform self-diagnostic result of ABS and record all active DTCs.
2. Clear all DTCs.
3. Perform DTC confirmation procedure. Refer to
.
Does DTC C1101, C1102, C1103 or C1104 reset?
YES
>> GO TO 2.
NO
>> Refer to
GI-41, "Intermittent Incident"
.
2.
INSPECT WHEEL SENSOR
Inspect the suspect wheel sensor for damage or deformation.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace as necessary.
3.
HARNESS AND CONNECTOR INSPECTION
DTC
Display Item
Malfunction detected condition
Possible causes
C1101
RR RH SENSOR-1
• When power supply voltage of rear wheel sensor
RH is low.
• When an open or shorted circuit is detected in rear
wheel sensor RH circuit.
• Harness or connector
• Wheel sensor
• ABS actuator and electric unit
(control unit)
C1102
RR LH SENSOR-1
• When power supply voltage of rear wheel sensor
LH is low.
• When an open or shorted circuit is detected in rear
wheel sensor LH circuit.
C1103
FR RH SENSOR-1
• When power supply voltage of front wheel sensor
RH is low.
• When an open or shorted circuit is detected in front
wheel sensor RH circuit.
C1104
FR LH SENSOR-1
• When power supply voltage of front wheel sensor
LH is low.
• When an open or shorted circuit is detected in front
wheel sensor LH circuit.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст