Nissan Versa Note. Manual — part 520
INL-48
< DTC/CIRCUIT DIAGNOSIS >
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
Description
INFOID:0000000009695427
Provides the power supply and the ground to control the push-button ignition switch illumination.
Component Function Check
INFOID:0000000009695428
1.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION OPERATION
CONSULT
1. Turn the ignition switch ON.
2. Select ENGINE SW ILLUMI of BCM (INTELLGENT KEY) active test item.
3. While operating the test item, check that the push-button ignition switch illumination turns ON/OFF
Is the inspection result normal?
YES
>> Push-button ignition switch illumination circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009695429
Regarding Wiring Diagram information, refer to
.
1.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION OPERATION
CONSULT
1. Turn the ignition switch ON.
2. Select ENGINE SW ILLUMI of BCM (INTELLIGENT KEY) active test item.
3. While operating the test item, check voltage between push-button ignition switch connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION POWER SUPPLY OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect BCM connector and push-button ignition switch connector.
3. Check continuity between BCM connector and push-button ignition switch connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the harness or connectors.
ON
: Push-button ignition switch illumination ON
OFF
: Push-button ignition switch illumination OFF
Terminals
Test item
Voltage
(+)
(-)
Push-button ignition switch
Ground
ENGINE SW ILLUMI
Connector
Terminal
M25
5
ON
Battery voltage
OFF
0 V
BCM
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
M98
90
M25
5
Yes
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
INL-49
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
3.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION POWER SUPPLY SHORT CIRCUIT
Check continuity between BCM connector M98 terminal 90 and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-70, "Removal and Installation"
NO
>> Repair or replace the harness or connectors.
4.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION GROUND CIRCUIT
1. Turn the ignition switch OFF
2. Disconnect push-button ignition switch connector.
3. Check continuity between push-button ignition switch connector and ground.
Is the inspection result normal?
YES
>> Replace push-button ignition switch. Refer to
PCS-103, "Removal and Installation"
.
NO
>> GO TO 5.
5.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION GROUND OPEN CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM connector and push-button ignition switch connector.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-70, "Removal and Installation"
NO
>> Repair or replace the harness or connectors.
BCM
Ground
Continuity
Connector
Terminal
M98
90
No
Push-button ignition switch
Ground
Continuity
Connector
Terminal
M25
6
Yes
BCM
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
M98
92
M25
6
Yes
INL-50
< SYMPTOM DIAGNOSIS >
INTERIOR LIGHTING SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
INTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000009643000
CAUTION:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagno-
sis if any DTC is detected.
Symptom
Possible cause
Inspection item
• Interior room lamp does not turn ON even though the
door is open.
(It turns ON when turning the interior room lamp ON.)
• Interior room lamp does not turn OFF even though
the door is closed.
• Harness between BCM and each
door switch
• Harness between BCM and each
interior room lamp
• BCM
Door switch circuit
Refer to
(with Intelligent Key)
or
(without Intelligent Key).
Interior room lamp control circuit
Refer to
.
Interior room lamp timer does not activate.
(It turns ON/ OFF when the door opens/closes.)
—
Check the interior room lamp setting.
Refer to
(with Intelligent Key) or
(without Intelligent Key).
Interior room lamp battery saver does not activate.
—
Check the interior room lamp battery
saver setting.
Refer to
(without Intelligent Key).
Cargo lamp does not turn ON even though the back
door is open.
(It turns ON when turning the cargo lamp ON.)
• Harness between BCM and car-
go lamp
• Harness between BCM and back
door switch
• BCM
Back door switch circuit
Refer to
(with Intelligent Key)
or
(without Intelligent Key).
Cargo lamp circuit
Refer to
.
MAP LAMP
INL-51
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
REMOVAL AND INSTALLATION
MAP LAMP
Exploded View
INFOID:0000000008969463
Removal and Installation
INFOID:0000000008969464
REMOVAL
1. Release lens pawls using a suitable tool (A) and remove.
: Pawl
2. Release map lamp pawl using suitable tool (A).
: Pawl
3. Disconnect the harness connector from map lamp and remove.
INSTALLATION
Installation is in the reverse order of removal.
Bulb Replacement
INFOID:0000000008969465
WARNING:
1.
Map lamp
2.
Bulb
3.
Lens
Pawl
AWLIA2175ZZ
AWLIA2150ZZ
AWLIA2144ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст