Nissan Versa Note. Manual — part 882
WASHER MOTOR CIRCUIT
WW-47
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WASHER MOTOR CIRCUIT
Diagnosis Procedure
INFOID:0000000009643032
Regarding Wiring Diagram information, refer to
,
1.
CHECK FRONT AND REAR WASHER MOTOR FUSE
1. Turn the ignition switch OFF.
2. Check that the following fuse is not blown.
Is the fuse blown?
YES
>> Replace the fuse after repairing the affected circuit.
NO
>> GO TO 2.
2.
CHECK FRONT AND REAR WASHER MOTOR POWER SUPPLY
1. Disconnect front and rear washer motor.
2. Turn ignition switch ON.
3. Check voltage between front and rear washer motor harness connector and ground.
Front washer operation
Rear washer operation
Is the inspection result normal?
YES
>> Replace front and rear washer motor. Refer to
WW-63, "Removal and Installation"
NO
>> GO TO 3.
3.
CHECK WASHER SWITCH
Check washer switch. Refer to
Is the inspection result normal?
YES
>> Repair harness between front and rear washer motor and washer switch.
NO
>> Replace washer switch. Refer to
BCS-71, "Removal and Installation"
(with Intelligent Key) or
BCS-128, "Removal and Installation"
(without Intelligent Key).
Component
Capacity
Fuse No.
Location
Front and rear washer motor
10A
6
Fuse block (J/B)
Front and rear washer motor
Ground
Washer switch
Voltage
(Approx.)
Connector
Terminal
OFF
0
E2
1
ON
Battery voltage
Front and rear washer motor
Ground
Washer switch
Voltage
(Approx.)
Connector
Terminal
OFF
0
E2
2
ON
Battery voltage
WW-48
< DTC/CIRCUIT DIAGNOSIS >
WASHER SWITCH
WASHER SWITCH
Description
INFOID:0000000009643033
• Washer switch is integrated with the combination switch.
• Combination switch (wiper and washer switch) switches polarity between front washer operating and rear
washer operating to supply power and ground to the front and rear washer motor.
Component Inspection
INFOID:0000000009643034
1.
CHECK FRONT WASHER SWITCH
1. Turn the ignition switch OFF.
2. Disconnect combination switch (wiper and washer switch).
3. Check continuity between the combination switch (wiper and washer switch) terminals.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace combination switch (wiper and washer switch). Refer to
BCS-71, "Removal and Installa-
(with Intelligent Key) or
BCS-128, "Removal and Installation"
2.
CHECK REAR WASHER SWITCH
1. Check continuity between the combination switch (wiper and washer switch) terminals.
ALLIA0350GB
A: Terminal 4
B: Terminal 6
C: Terminal 3
D: Terminal 1
JPLIA0164GB
Combination switch (wiper and washer
switch)
Condition
Continuity
Terminal
1
6
Front washer switch ON
Yes
3
4
WASHER SWITCH
WW-49
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Is the inspection result normal?
YES
>> Wiper and washer switch is normal.
NO
>> Replace combination switch (wiper and washer switch). Refer to
BCS-71, "Removal and Installa-
(with Intelligent Key) or
BCS-128, "Removal and Installation"
A: Terminal 4
B: Terminal 6
C: Terminal 3
D: Terminal 1
JPLIA0164GB
Combination switch (wiper and washer
switch)
Condition
Continuity
Terminal
1
4
Rear washer switch ON
Yes
6
3
WW-50
< DTC/CIRCUIT DIAGNOSIS >
REAR WIPER MOTOR CIRCUIT
REAR WIPER MOTOR CIRCUIT
Component Function Check
INFOID:0000000009643035
1.
CHECK REAR WIPER ON OPERATION
CONSULT ACTIVE TEST
1. Select "RR WIPER" of BCM active test item.
2. While operating the test item, check rear wiper operation.
Is rear wiper operation normal?
YES
>> Rear wiper motor circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009643036
Regarding Wiring Diagram information, refer to
.
1.
CHECK REAR WIPER MOTOR OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1. Turn the ignition switch OFF.
2. Disconnect rear wiper motor.
3. Turn the ignition switch ON.
4. Select RR WIPER of BCM active test item.
5. While operating the test item, check voltage between BCM harness connector and ground.
With Intelligent Key
Without Intelligent Key
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK REAR WIPER MOTOR GROUND CIRCUIT
1. Turn the ignition switch OFF.
2. Check continuity between rear wiper motor harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear wiper motor. Refer to
WW-77, "Removal and Installation"
.
NO
>> Repair or replace harness.
ON
: Rear wiper ON operation
OFF
: Stop the rear wiper.
BCM
Ground
Test item
Voltage
(Approx.)
Connector
Terminal
REAR WIPER
M100
54
ON
Battery voltage
OFF
0V
BCM
Ground
Test item
Voltage
(Approx.)
Connector
Terminal
REAR WIPER
M20
68
ON
Battery voltage
OFF
0V
Rear wiper motor
Ground
Continuity
Connector
Terminal
D502
4
Yes
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст