Nissan Versa Note. Manual — part 700
B2556 PUSH-BUTTON IGNITION SWITCH
SEC-79
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2556 PUSH-BUTTON IGNITION SWITCH
DTC Logic
INFOID:0000000009705880
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Press push-button ignition switch under the following condition.
-
Brake pedal: Not depressed
2. Release push-button ignition switch and wait 100 seconds or more.
3. Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009705881
Regarding Wiring Diagram information, refer to
.
1.
CHECK PUSH-BUTTON IGNITION SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect push-button ignition switch connector.
3. Check voltage between push-button ignition switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT
1. Disconnect BCM connector and IPDM E/R connector.
2. Check continuity between push-button ignition switch harness connector and BCM harness connector.
3. Check continuity between push-button ignition switch harness connector and ground.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2556
ENG START SW
BCM detects the push-button ignition switch
stuck at ON for 100 seconds or more.
• Harness or connectors
(Push-button ignition switch circuit is
shorted.)
• Push-button ignition switch
• BCM
(+)
(–)
Voltage (V)
(Approx.)
Push-button ignition switch
Connector
Terminal
M25
8
Ground
12
Push-button ignition switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
M25
8
M98
76
Yes
Push-button ignition switch
Ground
Continuity
Connector
Terminal
M25
8
No
SEC-80
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2556 PUSH-BUTTON IGNITION SWITCH
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
REPLACE BCM
1. Replace BCM. Refer to
BCS-70, "Removal and Installation"
.
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-
SULT Immobilizer mode and follow the on-screen instructions.
>> Inspection End.
4.
CHECK PUSH-BUTTON IGNITION SWITCH GROUND CIRCUIT
Check continuity between push-button ignition switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK PUSH-BUTTON IGNITION SWITCH
SEC-80, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace push-button ignition switch. Refer to
SEC-127, "Removal and Installation"
.
6.
CHECK INTERMITTENT INCIDENT
GI-41, "Intermittent Incident"
>> Inspection End.
Component Inspection
INFOID:0000000009705882
1.
CHECK PUSH-BUTTON IGNITION SWITCH
1. Turn ignition switch OFF.
2. Disconnect push-button ignition switch connector.
3. Check continuity between push-button ignition switch terminals.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace push-button ignition switch. Refer to
SEC-127, "Removal and Installation"
.
Push-button ignition switch
Ground
Continuity
Connector
Terminal
M25
4
Yes
Push-button ignition switch
Condition
Continuity
Terminal
4
8
Push-button ignition
switch
Pressed
Yes
Not pressed
No
B2557 VEHICLE SPEED
SEC-81
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2557 VEHICLE SPEED
DTC Logic
INFOID:0000000009705883
DTC DETECTION LOGIC
NOTE:
• If DTC B2557 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B2557 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and wait 10 seconds or more.
2. Drive the vehicle at a vehicle speed of 10 km/h (6.2 MPH) or more for 10 seconds or more.
3. Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009705884
1.
CHECK DTC OF “ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)”
Check DTC in Self Diagnostic Result mode of ABS using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
.
NO
>> GO TO 2.
2.
CHECK DTC OF COMBINATION METER
Check DTC in Self Diagnostic Result mode of METER/M&A using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
.
NO
>> GO TO 3.
3.
CHECK INTERMITTENT INCIDENT
GI-41, "Intermittent Incident"
.
>> Inspection End.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible causes
B2557
VEHICLE SPEED
BCM detects one of the following conditions for 10
seconds continuously.
• Vehicle speed signal from “combination meter”
is 10 km/h (6.2 MPH) or more and vehicle
speed signal from “ABS actuator and electric
unit (control unit)” is 4 km/h (2.5 MPH) or less
• Vehicle speed signal from “combination meter”
is 4 km/h (2.5 MPH) or less and vehicle speed
signal from “ABS actuator and electric unit
(control unit)” is 10 km/h (6.2 MPH) or more
• Harness or connectors
(The CAN communication line is
open or shorted.)
• Combination meter
• ABS actuator and electric unit
(control unit)
SEC-82
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2601 SHIFT POSITION
B2601 SHIFT POSITION
DTC Logic
INFOID:0000000009705885
DTC DETECTION LOGIC
NOTE:
• If DTC B2601 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B2601 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Shift the selector lever to the P position.
2. Turn ignition switch ON and wait 2 seconds or more.
3. Shift the selector lever to any position other than P and wait 2 seconds or more.
4. Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009705886
Regarding Wiring Diagram information, refer to
.
1.
CHECK CVT SHIFT SELECTOR CIRCUIT (BCM)
1. Turn ignition switch OFF.
2. Disconnect CVT shift selector (park position switch) connector.
3. Disconnect BCM connector.
4. Check continuity between CVT shift selector (park position switch) harness connector and BCM harness
connector.
5. Check continuity between CVT shift selector (park position switch) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2601
SHIFT P SIGNAL
When there is a difference between P range
signal from CVT shift selector (park position
switch) and P position signal from IPDM E/R
(CAN).
• Harness or connectors
(CAN communication line is open or
shorted.)
• Harness or connectors
[CVT shift selector (park position
switch) circuit is open or shorted.]
• IPDM E/R
• BCM
CVT shift selector (park position switch)
BCM
Continuity
Connector
Terminal
Connector
Terminal
M38
8
M97
37
Yes
CVT shift selector (park position switch)
Ground
Continuity
Connector
Terminal
M38
8
No
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст