Nissan Versa Note. Manual — part 455
EVAP CONTROL SYSTEM PRESSURE SENSOR
FL-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
EVAP CONTROL SYSTEM PRESSURE SENSOR
Exploded View
INFOID:0000000009445756
Removal and Installation
INFOID:0000000009445757
NOTE:
The EVAP canister vent control valve and EVAP canister system pressure sensor can be removed without
removing the EVAP canister.
REMOVAL
1. Disconnect EVAP canister control system pressure sensor harness connector.
2. Remove EVAP canister control system pressure sensor and O-ring.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse O-ring.
1.
EVAP control system pressure sensor 2.
O-ring
3.
EVAP canister protector
4.
Hose clamp
5.
EVAP canister purge hose
6.
EVAP vent line
7.
EVAP canister vent control valve hose 8.
EVAP canister vent control valve
9.
O-ring
10. EVAP canister
Pawl
Front
AWBIA1593ZZ
FL-20
< DISASSEMBLY AND ASSEMBLY >
FUEL LEVEL SENSOR UNIT
DISASSEMBLY AND ASSEMBLY
FUEL LEVEL SENSOR UNIT
Exploded View
INFOID:0000000009405638
Fuel Level Sensor Unit
Disassembly and Assembly
INFOID:0000000009405639
DISASSEMBLY
1. Disconnect fuel level sensor unit/fuel tank temperature sensor
harness connectors (1).
NOTE:
Hold connector with your fingers, because there is no tab for
releasing stopper. Pull it out straight downward.
ALBIA1132ZZ
1. Fuel filter and pump assembly 2. Float arm assembly
3. Fuel tank temperature sensor
4. Fuel level sensor unit
5. Fuel level sensor unit/fuel tank temperature sensor harness
connector
AWBIA1590ZZ
FUEL LEVEL SENSOR UNIT
FL-21
< DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
2. Remove fuel tank temperature sensor (2) from fuel filter and fuel
pump assembly (1).
3. Using a suitable tool push tab (A) in the direction (
) shown
and remove fuel level sensor unit (2) from fuel filter and fuel
pump assembly (1).
CAUTION:
• Be careful not to damage the fuel level sensor unit.
• Do not disassemble fuel filter and fuel pump assembly.
ASSEMBLY
1. Check for damage of fuel level sensor unit installation position on the side of fuel filter and pump assem-
bly.
2. Slide fuel level sensor unit until it aligns to installation groove, then insert it until it stops.
• After inserting, apply force in reverse direction (removal direction) to ensure it cannot be pulled out.
3. Connect fuel level sensor unit/fuel tank temperature sensor harness connector.
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leaks.
1. Turn ignition switch “ON” (with engine stopped), then check fuel system connections for leaks by applying
fuel pressure to fuel piping.
2. Start engine and let it idle and check there are no fuel leaks at the fuel system connections.
ALBIA1134ZZ
ALBIA1135ZZ
FL-22
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Fuel Tank
INFOID:0000000008969008
Standard and Limit
Unit: (US gal, lmp gal)
Fuel tank capacity
Approx. 41.0 (10-7/8 US gal, 9.0 Imp gal)
Fuel recommendation
Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст