Nissan Versa Note. Manual — part 575
MA-36
< PERIODIC MAINTENANCE >
CHASSIS AND BODY MAINTENANCE
1. Check that there is no foreign material in the reservoir tank, and
refill with new brake fluid. Refer to
2. Loosen the bleeder valve, slowly depress the brake pedal to the
full stroke, and then release the pedal. Repeat this operation at
intervals of 2 or 3 seconds until new brake fluid is discharged.
Then close the bleeder valve with the brake pedal depressed.
Repeat the same work on each wheel.
3. Perform the air bleeding procedure. Refer to
FLUID : Bleeding Brake System"
.
BRAKE FLUID : Bleeding Brake System
INFOID:0000000009681972
CAUTION:
• Turn the ignition switch OFF and disconnect ABS actuator and electric unit (control unit) or battery
negative terminal before performing the work.
• Monitor the fluid level in the reservoir tank while performing the air bleeding.
• Do not spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe
it off immediately and wash with water if it gets on a painted surface.
• Always use new brake fluid for refilling. Do not reuse drained brake fluid.
• Do not allow foreign matter (e.g. dust) and oils other than brake fluid to enter the reservoir tank.
1. Connect a vinyl tube to the bleeder valve.
2. Fully depress the brake pedal 4 to 5 times.
3. Loosen the bleeder valve and bleed air with the brake pedal depressed, and then quickly tighten the
bleeder valve.
4. Repeat steps 2 and 3 until all of the air is out of the brake line.
5. Tighten the bleeder valve to the specified torque.
• Front disc brake: Refer to
BR-35, "BRAKE CALIPER ASSEMBLY : Exploded View"
.
6. Perform steps 1 to 5 in the following order: Front (RH) brake
→ front (LH) brake → rear (RH) brake → rear
(LH) brake.
7. Check that the fluid level in the reservoir tank is within the specified range after air bleeding. Refer to
35, "BRAKE FLUID : Inspection"
8. Add brake fluid as necessary to keep the brake fluid level within the specified range. Refer to
9. Inspect the brake pedal height and play. Adjust it if the measurement value is not the standard. Refer to
BR-8, "Inspection and Adjustment"
DISC BRAKE
DISC BRAKE : Inspection
INFOID:0000000009681973
INSPECTION
Check brake pad wear thickness from an inspection hole on cylinder
body. Check using a scale if necessary.
PFIA0403J
Wear thickness
: Refer to
.
BRA0010D
CHASSIS AND BODY MAINTENANCE
MA-37
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
DISC BRAKE : Brake Burnishing
INFOID:0000000009681974
BRAKE BURNISHING
Burnish contact surfaces between disc brake rotor and brake pads according to the following procedure after
refinishing disc brake rotors, replacing disc brake rotors, replacing brake pads, or if a soft pedal occurs at very
low mileage:
CAUTION:
• Be careful of vehicle speed because the brake pedal does not operate firmly/securely until pads and
disc brake rotor are securely seated.
• Only perform this procedure under safe road and traffic conditions. Use extreme caution.
1. Drive vehicle on straight, flat road.
2. Depress brake pedal with the power to stop vehicle within 3 to 5 seconds until the vehicle stops.
3. Drive without depressing brake pedal for a few minutes to cool the brakes.
4. Repeat steps 1 to 3 until pad and disc brake rotor are securely seated.
DISC BRAKE : Inspection
INFOID:0000000009681975
INSPECTION
Appearance
Check surface of disc brake rotor for uneven wear, cracks, and serious damage. Replace it if necessary. Refer
to
Runout
1. Secure the disc brake rotor to the wheel hub with wheel nuts (2
points at least).
2. Check the wheel bearing axial end play before the inspection.
.
3. Inspect the runout with a dial indicator to measure at 10 mm
(0.39 in) inside the disc edge.
4. Find the installation position that has a minimum runout by shift-
ing the disc brake rotor-to-wheel hub installation position by one
hole at a time if the runout exceeds the limit value.
5. Refinish or replace the disc brake rotor if the runout is outside the limit even after performing the above
operation.
CAUTION:
If the thickness is less than wear thickness + 0.3 mm (0.012 in), replace the disc brake rotor. Refer
BR-36, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
Thickness
Check the thickness of the disc brake rotor using a micrometer.
Replace the disc brake rotor if the thickness is below the wear limit.
DRUM BRAKE
Runout
: Refer to
Wear thickness
: Refer to
BRA0013D
Wear thickness
: Refer to
.
Thickness variation (mea-
sured at 8 positions)
: Refer to
.
SBR020B
MA-38
< PERIODIC MAINTENANCE >
CHASSIS AND BODY MAINTENANCE
DRUM BRAKE : Inspection
INFOID:0000000009681976
INSPECTION
Brake Lining
1. Remove plug from back plate. Refer to
.
2. Check brake lining wear thickness (A) from an inspection hole
on back plate. Check using a scale if necessary.
DRUM BRAKE : Brake Burnishing
INFOID:0000000009681977
BRAKE BURNISHING
Burnish contact surfaces between brake lining and brake drum according to the following procedure after
refinishing brake drum, replacing brake drum, replacing brake lining, or if a soft pedal occurs at very low mile-
age:
CAUTION:
• Be careful of vehicle speed because the brake pedal does not operate firmly/securely until brake lin-
ing and brake drum are securely seated.
• Only perform this procedure under safe road and traffic conditions. Use extreme caution.
1. Drive vehicle on straight, flat road.
2. Depress brake pedal with the power to stop vehicle within 3 to 5 seconds until the vehicle stops.
3. Drive without depressing brake pedal for a few minutes to cool the brake.
4. Repeat steps 1 to 3 until brake lining and brake drum are securely seated.
DRUM BRAKE : Inspection
INFOID:0000000009681978
INSPECTION
Appearance
Check surface of brake drum for uneven wear, cracks and serious damage. Replace it if necessary. Refer to
RAX-6, "Removal and Installation"
.
NOTE:
• Make sure the parking brake control is fully released prior to removal of the brake drum.
• The rear wheel hub is part of the brake drum.
Brake Drum Inner Diameter
Wear thickness
: Refer to
.
JSFIA1039ZZ
CHASSIS AND BODY MAINTENANCE
MA-39
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
Check inner diameter (B) of the brake drum.
STEERING GEAR AND LINKAGE
STEERING GEAR AND LINKAGE : Inspection
INFOID:0000000009417542
STEERING GEAR
• Check gear housing and boots for looseness, damage and grease
leakage.
• Check connection with steering column for looseness.
STEERING LINKAGE
Check ball joint, dust cover and other component parts for looseness, wear, damage and grease leakage.
AXLE AND SUSPENSION PARTS
AXLE AND SUSPENSION PARTS : Inspection
INFOID:0000000009417543
Check front and rear axle and suspension parts for excessive play,
cracks, wear or other damage.
• Shake each wheel to check for excessive play.
• Check wheel bearings for smooth operation.
• Check axle and suspension nuts and bolts for looseness.
• Check strut (shock absorber) for oil leakage or other damage.
• Check suspension ball joint for grease leakage and ball joint dust
cover for cracks or other damage.
DRIVE SHAFT
Inner diameter : Refer to
JPFIA0113ZZ
JPPIA0013GB
SMA525A
SFA392B
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст