Nissan Versa Note. Manual — part 240
HORN FUNCTION
DLK-245
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HORN FUNCTION
Description
INFOID:0000000009645404
Perform answer-back for each operation with horn.
Component Function Check
INFOID:0000000009645405
1.
CHECK FUNCTION
1. Select HORN in “ACTIVE TEST” mode with CONSULT.
2. Check the horn operation.
Is the operation normal?
YES
>> Inspection End.
NO
>> Refer to
DLK-245, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000009645406
Regarding Wiring Diagram information, refer to
.
1.
CHECK HORN FUNCTION
Check horn function with horn switch.
Does the horn sound?
YES
>> GO TO 2
NO
>> Refer to
.
2.
CHECK HORN RELAY POWER SUPPLY
1. Turn ignition switch ON.
2. Perform “ACTIVE TEST” (“HORN”) with CONSULT.
3. Using an oscilloscope or analog voltmeter to check voltage between IPDM E/R connector and ground.
Is the inspection result normal?
YES
>> Repair or replace open harness between IPDM E/R and horn relay.
NO
>> GO TO 3
3.
CHECK HORN RELAY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R and horn relay connector.
3. Check continuity between IPDM E/R harness connector and horn relay harness connector.
4. Check continuity between IPDM E/R harness connector and ground.
Test item
Description
HORN
ON
Horn relay
ON (for 20 ms)
IPDM E/R
Ground
Test item
Voltage (V)
(Approx.)
Connector
Terminal
E46
73
Ground
HORN
ON
Battery voltage
→ 0 → Battery voltage
Other than above
Battery voltage
IPDM E/R
Horn relay
Continuity
Connector
Terminal
Connector
Terminal
E46
73
E39
1
Yes
DLK-246
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
HORN FUNCTION
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair or replace harness.
4.
CHECK INTERMITTENT INCIDENT
GI-41, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-60, "Removal and Installation"
NO
>> Repair or replace the malfunctioning part.
IPDM E/R
Ground
Continuity
Connector
Terminal
E46
73
Ground
No
WARNING CHIME FUNCTION
DLK-247
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
WARNING CHIME FUNCTION
Description
INFOID:0000000009645407
Performs operation method guide and warning with buzzer.
Component Function Check
INFOID:0000000009645408
1.
CHECK FUNCTION
With CONSULT
1. Check the operation with “BUZZER” in the Active Test.
2. Touch “IGN KEY WARN ALM”, “SEAT BELT WARN TEST”or “LIGHT WARN ALM”on screen.
Is the inspection result normal?
YES
>> Warning buzzer into combination meter is OK.
NO
>> Refer to
DLK-247, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000009645409
1.
CHECK METER BUZZER CIRCUIT
Operate the hazard lights by turning ON the hazard warning switch.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Replace combination meter. Refer to
MWI-54, "Removal and Installation"
2.
CHECK INTERMITTENT INCIDENT
GI-41, "Intermittent Incident"
.
>> Inspection End.
DLK-248
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
HAZARD FUNCTION
HAZARD FUNCTION
Description
INFOID:0000000009645410
Perform answer-back for each operation with number of blinks.
Component Function Check
INFOID:0000000009645411
1.
CHECK FUNCTION
Check hazard warning lamp (“FLASHER”) in Active Test.
Is the inspection result normal?
YES
>> Hazard warning lamp circuit is OK.
NO
>> Refer to
DLK-248, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000009645412
1.
CHECK HAZARD SWITCH CIRCUIT
Operate the hazard lights by turning ON the hazard warning switch.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Repair or replace hazard warning switch circuit. Refer to
EXL-104, "Removal and Installation"
.
2.
CHECK INTERMITTENT INCIDENT
GI-41, "Intermittent Incident"
>> Inspection End.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст