Nissan Frontier D22. Manual — part 750
GI-32
SERVICE INFORMATION FOR ELECTRICAL INCIDENT
Control Unit Circuit Test
System Description:When the switch is ON, the control unit lights up the lamp.
INPUT-OUTPUT VOLTAGE CHART
The voltage value is based on the body ground.
*:If high resistance exists in the switch side circuit (caused by a single strand), terminal 1 does not detect battery voltage. Control unit
does not detect the switch is ON even if the switch does not turn ON. Therefore, the control unit does not supply power to light up the
lamp.
INPUT-OUTPUT VOLTAGE CHART
The voltage value is based on the body ground.
*:If high resistance exists in the switch side circuit (caused by a single strand), terminal 2 does not detect approx. 0V. Control unit does
not detect the switch is ON even if the switch does not turn ON. Therefore, the control unit does not control ground to light up the lamp.
MGI034A
Pin
No.
Item
Condition
Voltage
value [V]
In case of high resistance such as single strand [V] *
1
Switch
Switch ON
Battery voltage
Lower than battery voltage Approx. 8 (Example)
Switch OFF
Approx. 0
Approx. 0
2
Lamp
Switch ON
Battery voltage
Approx. 0 (Inoperative lamp)
Switch OFF
Approx. 0
Approx. 0
MGI035A
Pin
No.
Item
Condition
Voltage
value [V]
In case of high resistance such as single strand [V] *
1
Lamp
Switch ON
Approx. 0
Battery voltage (Inoperative lamp)
Switch OFF
Battery voltage
Battery voltage
2
Switch
Switch ON
Approx. 0
Higher than 0 Approx. 4 (Example)
Switch OFF
Approx. 5
Approx. 5
SERVICE INFORMATION FOR ELECTRICAL INCIDENT
GI-33
C
D
E
F
G
H
I
J
K
L
M
B
GI
Control Units and Electrical Parts
EAS0012M
PRECAUTIONS
●
Never reverse polarity of battery terminals.
●
Install only parts specified for a vehicle.
●
Before replacing the control unit, check the input and output and
functions of the component parts.
●
Do not apply excessive force when disconnecting a connector.
●
If a connector is installed by tightening bolts, loosen bolt mount-
ing it, then take it out by hand.
●
Before installing a connector, make sure the terminal is not bent
or damaged, and then correctly connect it.
When installing a connector by tightening bolts, fix it by tighten-
ing the mounting bolt until the painted projection of the connec-
tor becomes even with the surface.
●
For removal of the lever type connector, pull the lever up to the
direction pointed to by the arrow A in the figure, and then
remove the connector.
●
For installation of the lever type connector, pull down the lever to
the direction pointed by the arrow B in the figure, and then push
the connector until a clicking noise is heard.
SAIA0251E
SAIA0252E
SAIA0253E
SAIA0254E
GI-34
SERVICE INFORMATION FOR ELECTRICAL INCIDENT
●
Do not apply excessive shock to the control unit by dropping or
hitting it.
●
Be careful to prevent condensation in the control unit due to
rapid temperature changes and do not let water or rain get on it.
If water is found in the control unit, dry it fully and then install it in
the vehicle.
●
Be careful not to let oil to get on the control unit connector.
●
Avoid cleaning the control unit with volatile oil.
●
Do not disassemble the control unit, and do not remove the
upper and lower covers.
●
When using a DMM, be careful not to let test probes get close to
each other to prevent the power transistor in the control unit
from damaging battery voltage because of short circuiting.
●
When checking input and output signals of the control unit, use
the specified check adapter.
SMJ INSTALLATION
To install SMJ, tighten bolts until orange “fulltight” mark appears and
then retighten to specified torque as required.
CAUTION:
Do not overtighten bolts, otherwise, they may be damaged.
SAIA0255E
SEF348N
SMJ
:3 - 5 N·m (0.3 - 0.5 kg-m, 26 - 43 in-lb)
CEL969
CONSULT-II CHECKING SYSTEM
GI-35
C
D
E
F
G
H
I
J
K
L
M
B
GI
CONSULT-II CHECKING SYSTEM
PFP:00000
Description
EAS0012N
●
CONSULT-II is a hand-held type tester. When it is connected with a diagnostic connector equipped on the
vehicle side, it will communicate with the control unit equipped in the vehicle and then enable various
kinds of diagnostic tests.
●
Refer to “CONSULT Operator's Manual” for more information.
Function and System Application
EAS0012O
x: Applicable
*: For VG33E and VG33ER engine
Nickel Metal Hydride Battery Replacement
EAS0012P
CONSULT-II contains a nickel metal hydride battery. When replacing the battery obey the following:
WARNING:
Replace the nickel metal hydride battery with Genuine CONSULT-II battery only. Use of another bat-
tery may present a risk of fire or explosion. The battery may present a fire or chemical burn hazard if
mistreated. Do not recharge, disassemble or dispose of in fire.
Keep the battery out of reach of children and discard used battery conforming to the local regulations.
Checking Equipment
EAS0012Q
When ordering the below equipment, contact your NISSAN distributor.
Diagnostic test
mode
Function
Engine
A/T
Air bag
ABS
ABS
(Including
VDC)
Air
Pressure
Monitor
Work support
This mode enables a technician to
adjust some devices faster and more
accurately by following the indica-
tions on CONSULT-II.
x
—
—
—
x
x
DTC work
support
Select the operating condition to
confirm Diagnosis Trouble Codes.
—
x
—
—
—
—
Self-diagnostic
results
Self-diagnostic results can be read
and erased quickly.
x
x
x
x
x
x
Trouble diag-
nostic record
Current self-diagnostic results and
all trouble diagnostic records previ-
ously stored can be read.
—
—
x
—
—
—
ECU discrimi-
nated No.
Classification number of a replace-
ment ECU can be read to prevent an
incorrect ECU from being installed.
—
—
x
—
—
—
Data monitor
Input/Output data in the ECU (ECM)
can be read.
x
x
—
x
x
x
Data monitor
(Spec.)
The specified values will be dis-
played when an OK/NG judgment is
difficult for the DATA MONITOR
items by Bar Chart and Line Graph.
x
—
—
—
—
—
Active test
Diagnostic Test Mode in which CON-
SULT-II drives some actuators apart
from the ECUs and also shifts some
parameters in a specified range.
x
—
—
x
x
—
SRT & DTC
confirmation
The results of SRT (System Readi-
ness Test) and the self-diagnosis
status/result can be confirmed.
x
x*
—
—
—
—
ECU (ECM)
part number
ECU (ECM) part number can be
read.
x
x
—
x
x
x
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст