Nissan Frontier D22. Manual — part 217
METERS AND GAUGES
DI-17
C
D
E
F
G
H
I
J
L
M
A
B
DI
2.
CHECK HARNESS FOR OPEN OR SHORT
1.
Disconnect combination meter harness connector M39 and thermal transmitter harness connector F10
(except VG33ER) or F114 (with VG33ER).
2.
Check continuity between combination meter harness connector M39 terminal 46 (GY) and thermal trans-
mitter harness connector F10 (except VG33ER) terminal 1 (GY) or F114 (with VG33ER) terminal 1 (G/Y).
3.
Check continuity between combination meter harness connector M39 terminal 46 and ground.
OK or NG
OK
>> Thermal transmitter is OK.
NG
>> Repair harness or connector.
Continuity should exist.
Continuity should not exist.
WEL797A
DI-18
METERS AND GAUGES
Electrical Components Inspection
EKS006WA
FUEL LEVEL SENSOR UNIT CHECK
●
For removal, refer to
FL-6, "Removal and Installation"
With KA24DE
Check the resistance between fuel level sensor unit terminals 1 and 4.
*1 and *3: When float rod is in contact with stopper.
With VG33E and VG33ER
Check the resistance between fuel level sensor unit terminals G and E.
*1 and *3: When float rod is in contact with stopper.
THERMAL TRANSMITTER CHECK
Check the resistance between thermal transmitter terminal 1 and
body ground.
MEL827F
Ohmmeter
Float position
mm (in)
Resistance
value
(
Ω)
(Approx.)
(+)
(
−)
1
4
*1
Full
96 (3.78)
4 - 6
*2
1/2
188 (7.40)
30 - 34
*3
Empty
257 (10.12)
80 - 83
Ohmmeter
Float position
mm (in)
Resistance
value
(
Ω)
(Approx.)
(+)
(
−)
G
E
*1
Full
96 (3.78)
4 - 6
*2
1/2
188 (7.40)
30 - 34
*3
Empty
257 (10.12)
80 - 83
Water temperature
Resistance
value (
Ω)
(Approx.)
60
°C (140°F)
170 - 210
Ω
100
°C (212°F)
47 - 53
Ω
MEL424F
METERS AND GAUGES
DI-19
C
D
E
F
G
H
I
J
L
M
A
B
DI
VEHICLE SPEED SENSOR SIGNAL CHECK
1.
Remove vehicle speed sensor.
2.
Turn vehicle speed sensor pinion quickly and measure voltage
across 1 and 2.
LKIA0148E
DI-20
COMPASS AND THERMOMETER
COMPASS AND THERMOMETER
PFP:24835
System Description
EKS006WB
The compass and thermometer unit displays following items:
●
Earth magnetism and heading direction of vehicle.
●
Outside air temperature.
●
Caution for frozen road surfaces.
OUTSIDE TEMPERATURE DISPLAY
Push the mode switch when the ignition switch is in the ON position. The outside temperature will be displayed
in “
°F”.
●
Selecting the indication range
Push the switch to change from “
°F” to “°C”.
●
The indicated temperature on the thermometer is not readily affected by engine heat. It changes only
when one of the following conditions is present.
–
The temperature detected by the ambient air temperature sensor is lower than the indicated temperature
on the thermometer.
–
The vehicle speed is greater than 20 km/h (13 MPH).
(This is to prevent the indicated temperature from being affected by engine heat during low-speed driv-
ing.)
–
The ignition switch has been turned to the OFF position for more than 2 hours. (The engine is cold.)
DIRECTION DISPLAY
Push the switch with the ignition switch in the ON position. The direction will be displayed.
WEL901A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст