Nissan Frontier D22. Manual — part 880
RFD-28
[C200]
REAR FINAL DRIVE ASSEMBLY
6.
Select the correct pinion height adjusting washer.
7.
Remove the J34309 pinion preload shim selector Tool from the
final drive housing. Then disassemble to retrieve the pinion
bearings.
+5
Subtract 0.05 mm (0.0020 in)
+6
Subtract 0.06 mm (0.0024 in)
Pinion height adjust-
ing washer
:
Pinion head height number
Add or remove from the standard
pinion height adjusting washer thick-
ness measurement
SPD205A
REAR FINAL DRIVE ASSEMBLY
RFD-29
[C200]
C
E
F
G
H
I
J
K
L
M
A
B
RFD
TOOTH CONTACT
Checking gear tooth contact pattern is necessary to verify correct relationship between ring gear and drive pin-
ion.
Hypoid gear set which is not positioned properly may be noisy, or have short life or both. With the checking or
gear tooth contact pattern, the most desirable contact for low noise level and long life can be assured.
1.
Thoroughly clean ring gear and drive pinion teeth.
2.
Sparingly apply a mixture of powdered ferric oxide and oil or
equivalent to 3 or 4 teeth of ring gear drive side.
3.
Hold companion flange steady and rotate the ring gear in both
directions.
SPD199
SPD200
SPD007-B
RFD-30
[C200]
REAR FINAL DRIVE ASSEMBLY
ASSEMBLY OF DIFFERENTIAL CASE (WITHOUT LSD)
1.
Measure clearance between side gear thrust washer and differ-
ential case (4WD models).
The clearance can be adjusted with side gear thrust washer.
Refer to
RFD-38, "SIDE GEAR ADJUSTMENT (WITHOUT
2.
Install side gears, pinion mate gears and thrust washers into dif-
ferential case
3.
Apply gear oil to gear tooth surfaces and thrust surfaces and
check to see that they turn properly.
4.
Install differential case LH and RH (4WD models).
5.
Place differential case on ring gear.
6.
Apply Genuine Medium Strength Locking Sealant or equivalent
to ring gear bolts, and install them.
●
Refer to
MA-12, "RECOMMENDED FLUIDS AND LUBRI-
●
Tighten bolts in a crisscross pattern.
Clearance between side
gear thrust washer and
differential case (A – B)
: 0.10 - 0.20 mm (0.0039 -
0.0079 in)
SPD656
SPD643
Tool number
KV10112100 (BT8653-A)
Ring gear bolts
Step 1
: 53.9 - 63.7 N·m (5.5 - 6.4 kg-m,
40 - 46 ft-lb)
Step 2
: 34
° - 39° degrees rotation
SPD746
REAR FINAL DRIVE ASSEMBLY
RFD-31
[C200]
C
E
F
G
H
I
J
K
L
M
A
B
RFD
7.
Press-fit side bearing inner cones on differential case with Tool.
ASSEMBLY OF DIFFERENTIAL CASE (WITH LSD)
●
Prior to assembling discs and plates, properly lubricate them by dipping them in limited slip differential oil.
Refer to
MA-12, "RECOMMENDED FLUIDS AND LUBRICANTS"
.
1.
Alternately position specified number of friction plates and fric-
tion discs on rear of side gear.
●
Always position a friction plate first on rear of side gear.
2.
Install two spring plates.
Tool number A
: ST33230000 (J25805-01)
Tool number B
: ST33061000 (J8107-2)
PD353
Friction discs
: 2
Fiction plates
: 5
Spacer
: 1
SPD546A
SPD547A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст