Nissan Frontier D22. Manual — part 810
MT-46
[FS5R30A]
ON-VEHICLE SERVICE
ON-VEHICLE SERVICE
PFP:00000
Replacing Rear Oil Seal — 2WD Model
ECS007HY
REMOVAL
1.
Remove the propeller shaft. Refer to
2.
Remove rear oil seal using Tool.
●
Always replace with a new rear oil seal once it has been
removed.
INSTALLATION
1.
Install new rear oil seal until it stops.
●
Apply multi-purpose grease to seal lip of oil seal before install-
ing.
2.
Installation is in the reverse order of removal.
Position Switch Check
ECS007HZ
Tool number
: ST33290001 (J25810-A)
SMT479CA
Tool number
: ST33400001 (J26082)
SMT480CA
Switch
Gear position
Continuity
Back-up lamp switch
Reverse
Yes
Except reverse
No
Park/neutral position
(PNP) switch
Neutral
Yes
Except neutral
No
SMT981D
ON-VEHICLE SERVICE
MT-47
[FS5R30A]
D
E
F
G
H
I
J
K
L
M
A
B
MT
AMT205
MT-48
[FS5R30A]
TRANSMISSION ASSEMBLY
TRANSMISSION ASSEMBLY
PFP:32010
Removal and Installation
ECS007I0
REMOVAL
CAUTION:
When removing the M/T assembly from engine, first remove the crankshaft position sensor (OBD)
from the M/T assembly. Be careful not to damage sensor edge.
2WD Model
1.
Remove battery negative terminal.
2.
Remove shift lever.
3.
Remove crankshaft position sensor (OBD) from upper side of
transmission case.
4.
Remove operating cylinder from transmission. Refer to
5.
Disconnect vehicle speed sensor, back-up lamp switch, heated
oxygen sensor (rear) and park/neutral position (PNP) switch
harness connectors.
6.
Remove starter motor. Refer to
7.
Remove propeller shaft. Refer to
●
Insert plug into rear oil seal after removing propeller shaft.
●
Be careful not to damage spline, sleeve yoke and rear oil seal when removing propeller shaft.
8.
Remove gussets from transmission or engine.
9.
Remove exhaust tube mounting bracket from transmission. Refer to
.
10. Support manual transmission with a jack.
11. Remove rear mounting member. Refer to
EM-128, "Removal and Installation"
.
12. Lower manual transmission.
AMT189
SMT099A
TRANSMISSION ASSEMBLY
MT-49
[FS5R30A]
D
E
F
G
H
I
J
K
L
M
A
B
MT
WARNING:
Support manual transmission together with transfer while removing it.
4WD Model
1.
Disconnect the battery negative terminal.
2.
Remove shift lever from transmission and control lever from
transfer.
3.
Remove clutch operating cylinder from transmission. Refer to
.
4.
Disconnect the vehicle speed sensor, back-up lamp switch,
heated oxygen sensor (rear) and Park/neutral position (PNP)
switch harness connectors.
5.
Remove the starter motor. Refer to
.
6.
Remove front and rear propeller shafts. Refer to
●
Insert plug into rear oil seal after removing propeller shaft.
●
Be careful not to damage spline, sleeve yoke and rear oil seal when removing propeller shaft.
7.
Remove exhaust tube mounting bracket from transmission. Refer to
8.
Remove front exhaust tubes and center pipe.
9.
Remove the torsion bars and mounts. Refer to
10. Remove the rear torsion bar cross member.
11. Remove the gussets from the transmission or engine.
12. Support the manual transmission with a jack.
13. Remove rear mounting member. Refer to
EM-128, "Removal and Installation"
14. Lower manual transmission.
WARNING:
Support manual transmission together with transfer while removing it.
15. Remove crankshaft position sensor (OBD) from upper side of transmission case.
16. Remove transmission bolts.
WARNING:
Support manual transmission together with transfer while removing it.
AMT203
SMT558A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст