Nissan Frontier D22. Manual — part 935
WT-4
WHEEL
WHEEL
PFP:40300
Inspection
EES000XS
1.
Check tires for wear and improper inflation.
2.
Check wheels for deformation, cracks and other damage. If
deformed, remove wheel and check wheel runout.
a.
Remove tire from wheel and mount wheel on a tire balance
machine.
b.
Set dial indicator as shown in the illustration. Refer to
3.
Check front wheel bearings for looseness.
4.
Check front suspension for looseness.
SFA975B
WHEEL AND TIRE ASSEMBLY
WT-5
C
D
F
G
H
I
J
K
L
M
A
B
WT
WHEEL AND TIRE ASSEMBLY
PFP:40300
Balancing Wheels
EES000XT
REMOVAL
1.
Remove inner and outer balance weights from the wheel.
CAUTION:
●
Be careful not to scratch the wheel during removal.
2.
Using releasing agent, remove double-faced adhesive tape from the wheel.
CAUTION:
●
Be careful not to scratch the wheel during removal.
●
After removing double-faced adhesive tape, wipe clean traces of releasing agent from the
wheel.
WHEEL BALANCE ADJUSTMENT
●
If a tire balance machine has adhesion balance weight mode settings and drive-in weight mode setting,
select and adjust a drive-in weight mode suitable for wheels.
1.
Set wheel on wheel balancer using the center hole as a guide. Start the tire balance machine.
2.
When inner and outer imbalance values are shown on the wheel balancer indicator, multiply outer imbal-
ance value by 1.6 to determine balance weight that should be used. Select the outer balance weight with
a value closest to the calculated value and install it to the designated outer position of, or at the desig-
nated angle in relation to the road wheel.
CAUTION:
●
Do not install the inner balance weight before installing the outer balance weight.
●
Before installing the balance weight, be sure to clean the mating surface of the wheel.
Indicated imbalance value
× 5/3 = balance weight to be installed
Calculation example:
23 g (0.81 oz)
× 5/3 = 38.33 g (1.35 oz) = 40 g (1.41 oz) balance
weight (closer to calculated balance weight value)
Note that balance weight value must be closer to the calculated
balance weight value.
Example:
37.4 g = 35 g (1.23 oz)
37.5 g = 40 g (1.41 oz)
SMA054D
WT-6
WHEEL AND TIRE ASSEMBLY
a.
Install balance weight in the position shown.
b.
When installing balance weight to wheels, set it into the grooved
area on the inner wall of the wheel as shown so that the balance
weight center is aligned with the wheel balancer indication posi-
tion (angle).
CAUTION:
●
Always use genuine Nissan adhesion balance weights.
●
Balance weights are not reusable; always replace with
new ones.
●
Do not install more than three sheets of balance weights.
c.
If calculated balance weight value exceeds 50 g (1.76 oz), install
two balance weight sheets in line with each other as shown.
CAUTION:
Do not install one balance weight sheet on top of another.
3.
Start wheel balancer again.
4.
Install drive-in balance weight on inner side of road wheel in the
wheel balancer indication position (angle).
CAUTION:
Do not install more than two balance weights.
5.
Start wheel balancer. Make sure that inner and outer residual
imbalance values are 10 g (0.35 oz) each or below.
●
If either residual imbalance value exceeds 10 g (0.35 oz), repeat installation procedures.
Wheel balance (Maximum allowable imbalance):
Rotation
EES000XU
●
Follow the maintenance schedule for tire rotation service intervals. Refer to
.
●
Do not include the T-type spare tire when rotating the tires.
CAUTION:
When installing wheels, tighten them diagonally by dividing
the work two to three times in order to prevent the wheels
from developing any distortion.
SMA055D
Maximum allowable
imbalance
Dynamic (At rim flange)
10 g (0.35 oz) (one side)
Static
20 g (0.71 oz)
SMA056D
SMA829C
Tightening torque of wheel nut
: 118 - 147 N·m (12 - 15 kg-m, 87 - 108 ft-lb)
LOW TIRE PRESSURE WARNING SYSTEM
WT-7
C
D
F
G
H
I
J
K
L
M
A
B
WT
LOW TIRE PRESSURE WARNING SYSTEM
PFP:40300
System Components
EES000XV
System Description
EES000XW
TRANSMITTER (PRESSURE SENSOR)
A transmitter (pressure sensor) integrated with a valve is installed on
each wheel and transmits a detected air pressure signal in the form
of a radio wave.
LEIA0027E
LEIA0028E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст