Nissan Frontier D22. Manual — part 211
WATER PUMP
CO-27
[VG33E and VG33ER]
C
D
E
F
G
H
I
J
K
L
M
A
CO
2.
Apply a continuous bead of liquid gasket to mating surface of
water pump.
●
Use Genuine Anaerobic Liquid Gasket or equivalent.
Refer to
GI-42, "RECOMMENDED CHEMICAL PRODUCTS
3.
Installation is in the reverse order of removal.
●
When filling the radiator with coolant, refer to
MA-26, "REFILLING ENGINE COOLANT"
.
●
When installing the drive belts, refer to
ALC078
CO-28
[VG33E and VG33ER]
THERMOSTAT
THERMOSTAT
PFP:21200
Removal
EBS00GVY
●
Be careful not to spill coolant over engine compartment. Use a rag to absorb coolant.
1.
Drain engine coolant. Refer to
MA-26, "DRAINING ENGINE COOLANT"
2.
Remove radiator hoses (upper and lower) and fan shroud.
3.
Remove drive belts and pulley bracket.
4.
Remove water inlet and thermostat assembly.
Inspection
EBS00GVZ
1.
Check the thermostat valve seating condition at ordinary room temperature. The valve should seat tightly.
2.
Check valve opening temperature and valve lift.
3.
Check if valve closes at 5
°C (9°F) below valve opening temperature.
SLC081B
Description
VG33E
VG33ER
Valve opening
temperature
°C (°F)
82 (180)
76.5 (170)
Valve lift
mm/
°C (in/°F)
More than 10/95
(0.39/203)
More than 8 mm/90
°C
(0.31 in/194
°F)
SLC343
THERMOSTAT
CO-29
[VG33E and VG33ER]
C
D
E
F
G
H
I
J
K
L
M
A
CO
Installation
EBS00GW0
1.
Use a scraper to remove old liquid gasket from water inlet and engine mating surfaces.
2.
Apply a continuous bead of liquid gasket to mating surface of
water inlet.
●
Use Genuine Anaerobic Liquid Gasket or equivalent.
Refer to
GI-42, "RECOMMENDED CHEMICAL PRODUCTS
3.
Install thermostat with jiggle valve or air bleeder at upper side.
4.
Install water inlet housing.
5.
Install pulley bracket and drive belts.
6.
Install radiator hoses (upper and lower) and fan shroud.
7.
Refill engine coolant. Refer to
●
After installation, run engine for a few minutes, and
check for leaks.
SLC078B
SLC077B
CO-30
[VG33E and VG33ER]
RADIATOR
RADIATOR
PFP:21400
Components
EBS00GW1
Removal and Installation
EBS00GW2
1.
Remove undercover.
2.
Drain coolant from radiator drain plug. Refer to
MA-26, "DRAINING ENGINE COOLANT"
3.
Remove air duct (from mass air flow sensor to throttle body).
4.
Disconnect radiator upper and lower hoses.
5.
Remove A/T oil cooler hoses, if equipped.
6.
Remove radiator lower shroud.
7.
Disconnect reservoir tank hose.
8.
Remove the radiator.
9.
After repairing or replacing the radiator as necessary, installation is in the reverse order of removal.
10. Refill the engine cooling system. Refer to
MA-26, "REFILLING ENGINE COOLANT"
●
After installation, run the engine until it reaches operating temperature and check the system for leaks.
1.
Mounting rubber
2.
Radiator upper hose
3.
Radiator lower hose
4.
Radiator lower shroud
5.
Radiator upper shroud
6.
A/T oil cooler hoses
7.
Mounting rubber
8.
Radiator drain plug
9.
Radiator
10. Radiator filler cap
11.
Radiator reservoir
WBIA0240E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст