Nissan Frontier D22. Manual — part 907
SC-36
CHARGING SYSTEM
Construction
EKS006UY
Removal and Installation
EKS006UZ
KA24DE MODELS
Removal
1.
Remove engine undercover.
2.
Remove RH side splash shield.
3.
Disconnect harness connectors.
4.
Loosen adjustment bolt and remove belt.
5.
Remove two generator bolts and generator.
Installation
To install, reverse the removal procedure.
1.
Pulley assembly
2.
Front cover
3.
Front bearing
4.
Retainer
5.
Rotor
6.
Slip ring
7.
Stator
8.
Fan guide
9.
IC regulator assembly
10. Diode assembly
11. Packing
12. Rear cover
WKIA1652E
AEL676B
CHARGING SYSTEM
SC-37
C
D
E
F
G
H
I
J
L
M
A
B
SC
VG33E AND VG33ER MODELS
Removal
1.
Disconnect harness connectors.
2.
Remove engine undercover.
3.
Loosen adjustment bolt and remove belt.
4.
Remove three generator bolts and generator.
Installation
To install, reverse the removal procedure.
ASC012
SC-38
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
Battery
EKS006V0
Starter
EKS006V1
Generator
EKS006V2
Applied area
USA
Canada
Type
55D23R
65D26R
Capacity
V-AH
12-60
12-65
Cold cranking current
A
(For reference value)
356
413
Engine
KA24DE
VG33E and VG33ER
Type
M000T87381ZC
M000T87481ZC
MITSUBISHI make
Reduction gear type
System voltage
12V
No-load
Terminal voltage
11.0V
Current
Less than 90A
Revolution
More than 2,500 rpm
Minimum diameter of commutator
28.8 mm (1.134 in)
Minimum length of brush
7.0 mm (0.276 in)
Brush spring tension
5.8 - 21.6 N (0.59 - 2.20 kg, 1.30 - 4.86 lb)
Clearance of bearing metal and armature shaft
Less than 0.2 mm (0.008 in)
Clearance between pinion front edge and pinion
stopper
0.5 - 2.0 mm (0.02 - 0.079 in)
Type
LR-1100-736
LR-170-766
Nominal rating
12V - 100A
12V - 70A
Ground polarity
Negative
Negative
Minimum revolution under no-load (When
13.5 volts are applied)
Less than 1,000
Less than 1,000
Hot output current (When 13.5 volts are
applied)
More than 24A/1,300 rpm
More than 71A/2,500 rpm
More than 98A/5,000 rpm
More than 17A/1,300 rpm
More than 54A/2,500 rpm
More than 72A/5,000 rpm
Regulated output voltage
14.1 - 14.7V
14.1 - 14.7V
Minimum length of brush
6.0 mm (0.236 in)
6.0 mm (0.236 in)
Brush spring pressure
1.000 - 2.452 N (102 - 250 g, 3.60 - 8.82
oz)
1.000 - 2.452 N (102 - 250 g, 3.60 - 8.82
oz)
Slip ring minimum outer diameter
26.0 mm (1.024 in)
26.0 mm (1.024 in)
Rotor (Field coil) resistance
2.7
Ω
2.6
Ω
SE-1
SEAT
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION
A
B
SE
FRONT SEAT . . . . . . . . . . . . . . . .. 2
Removal and Installation . . . . . . . . . . .. 2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст