Nissan Frontier D22. Manual — part 890
RFD-68
[H233B]
REAR FINAL DRIVE ASSEMBLY
4.
Place pinion front bearing inner cone in gear carrier.
5.
Apply multi-purpose grease to cavity at sealing lips of oil seal.
Install front oil seal.
6.
Install drive pinion bearing spacer, pinion bearing adjusting shim
and drive pinion in gear carrier.
7.
Install ABS sensor unit and sensor rotor (2WD models).
8.
Insert companion flange onto drive pinion. Tap the companion
flange with a soft hammer until fully seated
9.
Tighten pinion nut until total preload is within specification.
●
The threaded portion of drive pinion and pinion nut
should be free from oil or grease.
SPD581
Tool number
A: ST30720000 (J-25405)
Tool number
B: KV38102510 (
—
)
SPD291A
SPD935-A
ABS sensor unit bolt
: 8 - 11 N·m (0.8 - 1.1 kg-m,
5.8 - 8.0 ft-lb)
SPD697
Tool number
: KV38108300 (J-44195)
Pinion nut
: 127 - 294 N·m (13.0 - 30.0 kg-m,
94 - 217 ft-lb)
Pinion preload
: 1.2 - 2.2 N·m (12 - 22 kg-m, 10 -
19 in-lb)
SPD481A
REAR FINAL DRIVE ASSEMBLY
RFD-69
[H233B]
C
E
F
G
H
I
J
K
L
M
A
B
RFD
10. Turn drive pinion in both directions several times, and measure
pinion bearing preload using Tool.
If preload is out of specification, adjust the thickness of spacer
and shim combination by replacing shim and spacer with thinner
one.
●
Start from the combination of thickest spacer and shim.
●
Combine each spacer and shim thickness one by one until the correct specification are achieved.
INSTALLATION OF DIFFERENTIAL CASE
1.
Install differential case assembly with side bearing outer races into gear carrier.
2.
Position side bearing adjusters on gear carrier with threads
properly engaged; using Tool, screw in adjusters lightly at this
stage of assembly.
3.
Align mark on bearing cap with that on gear carrier and install
bearing cap on gear carrier.
●
Do not tighten at this point. This allows further tightening of
side bearing adjusters.
4.
Tighten both right and left side bearing adjusters alternately and
measure ring gear backlash and total preload at the same time.
Adjust right and left side bearing adjusters by tightening them
alternately so that proper ring gear backlash and total preload
can be obtained.
Tool number
: ST3127S000 (J-25765-A)
Pinion bearing preload
(With front oil seal)
: 1.4 - 1.7 N·m (14 - 17 kg-cm,
12 - 15 in-lb)
Pinion bearing preload
(Without front oil seal)
: 1.2 - 1.5 N·m (12 - 15 kg-cm,
10 - 13 in-lb)
Drive pinion bearing
preload adjusting
spacer and shim
.
SPD149
Tool number
: ST32580000 (J-34312)
SPD684
SPD265
Ring gear-to-drive pinion
backlash
: 0.13 - 0.18 mm (0.0051 -
0.0071 in)
SPD246
RFD-70
[H233B]
REAR FINAL DRIVE ASSEMBLY
●
When checking preload, turn drive pinion in both direc-
tions several times to set bearing rollers using Tool.
5.
Tighten side bearing cap bolts.
6.
Install side lock finger in place to prevent rotation during opera-
tion.
7.
Check runout of ring gear with a dial indicator.
●
If backlash varies excessively in different places, the variance
may have resulted from foreign matter caught between the
ring gear and the differential case.
●
If the backlash varies greatly when the runout of the ring gear
is within a specified range, the hypoid gear set or differential
case should be replaced.
8.
Check tooth contact. Refer to
.
Tool number
: ST3127S000 (J-25765-A)
Total preload
: 1.7 - 2.5 N·m (17 - 25 kg-cm,
15 - 22 in-lb)
SPD149
Side bearing cap
bolts
: Refer to
SPD698
Ring gear runout limit
: 0.08 mm (0.0031 in)
SPD247
SERVICE DATA AND SPECIFICATIONS (SDS)
RFD-71
[H233B]
C
E
F
G
H
I
J
K
L
M
A
B
RFD
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
General Specifications
EDS00135
2WD MODEL
*: Standard on Canada models.
4WD MODEL
*: Standard on Canada models.
Ring Gear Runout
EDS00136
Side Gear Adjustment
EDS00137
*Always check with the Parts Department for the latest parts information.
Differential Torque Adjustment (LSD Models)
EDS00138
Engine
VG33E
VG33ER
Vehicle grade
XE
SE
SC
Rear final drive
Standard
Optional*
Standard
Standard
H233B
2-pinion
LSD
2-pinion
LSD
LSD
Gear ratio
4.636
4.900
4.363
Number of teeth (Ring gear/drive pinion)
51/11
49/10
48/11
Oil capacity (Approx.)
(US pt, lmp pt)
2.8 (5-7/8, 4-7/8)
Engine
VG33E
VG33ER
Vehicle grade
XE
SE
SC
Rear final drive
Standard
Optional
Standard
Optional*
Standard
H233B
2-pinion
LSD
2-pinion
LSD
LSD
Gear ratio
4.636
4.900
4.900
4.900
Number of teeth (Ring gear/drive pinion)
51/11
49/10
49/10
49/10
Oil capacity (Approx.)
(US pt, lmp pt)
2.8 (5-7/8, 4-7/8)
Ring gear runout limit
mm (in)
0.08 (0.0031)
Side gear backlash (Clearance between side gear thrust washer and dif-
ferential case)
mm (in)
0.10 - 0.20 (0.0039 - 0.0079)
Available
side gear
thrust wash-
ers
Thickness mm (in)
Part number*
1.75 (0.0689)
1.80 (0.0709)
1.85 (0.0728)
38424-T5000
38424-T5001
38424-T5002
Differential torque
N·m (kg-m, ft-lb)
40 - 58 (4.0 - 6.0, 29 - 43)
Number of discs and plates
Friction disc
Friction plate
Spring plate
Spacer
2
5
2
1
Wear limit of plate and disc
mm (in)
0.1 (0.004)
Allowable warping of friction disc and
plate
mm (in)
0.8 (0.0031)
Total thickness
mm (in)
18.57 - 20.43 (0.7311 - 0.8043)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст