Nissan Frontier D22. Manual — part 512
FUEL PUMP CIRCUIT
EC-1151
[VG33E]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than the ECM terminals, such as the ground.
Diagnostic Procedure
UBS00DQJ
1.
CHECK OVERALL FUNCTION
1.
Turn ignition switch ON.
2.
Pinch fuel feed hose with fingers.
Fuel pressure pulsation should be felt on the fuel feed hose
for 5 seconds after ignition switch is turned ON.
OK or NG
OK
>> INSPECTION END.
NG
>> GO TO 2.
2.
CHECK FUEL PUMP RELAY POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect fuel pump relay.
3.
Turn ignition switch ON.
4.
Check voltage between terminals 2, 5 and ground with CON-
SULT-II or tester.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 3.
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
11
W/R
Fuel pump relay
[Ignition switch: ON]
●
For a few seconds after turning ignition switch ON
[Engine is running]
0 - 1V
[Ignition switch: ON]
●
A few seconds after turning ignition switch ON
BATTERY VOLTAGE
(11 - 14V)
BBIA0422E
Voltage: Battery voltage
LEC103A
SEF674W
EC-1152
[VG33E]
FUEL PUMP CIRCUIT
3.
DETECT MALFUNCTIONING PART
Check the following.
●
Fuse block (J/B) connector M31
●
15A fuse
●
Harness for open or short between fuse and fuel pump relay
>> Repair harness or connectors.
4.
CHECK FUEL PUMP POWER SUPPLY AND GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect fuel pump harness connector.
3.
Check harness continuity between fuel pump terminal 2 and
body ground, fuel pump terminal 1 and fuel pump relay terminal
3. Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 6.
NG
>> GO TO 5.
5.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors M67, C1
●
Harness for open or short between fuel pump and body ground
●
Harness for open or short between fuel pump and fuel pump relay
>> Repair open circuit or short to ground or short to power in harness or connectors.
6.
CHECK FUEL PUMP RELAY OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Disconnect ECM harness connector.
2.
Check harness continuity between ECM terminal 11 and fuel pump relay terminal 1. Refer to Wiring Dia-
gram.
3.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 8.
NG
>> GO TO 7.
7.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors M81, F36
●
Harness for open or short between ECM and fuel pump relay
>> Repair open circuit or short to ground or short to power in harness or connectors.
Continuity should exist.
LEC764
Continuity should exist.
FUEL PUMP CIRCUIT
EC-1153
[VG33E]
C
D
E
F
G
H
I
J
K
L
M
A
EC
8.
CHECK FUEL PUMP RELAY
With CONSULT-II
1.
Reconnect fuel pump relay, fuel pump harness connector and ECM harness connector.
2.
Turn ignition switch ON.
3.
Turn fuel pump relay “ON” and “OFF” in “ACTIVE TEST” mode
with CONSULT-II and check operating sound.
Without CONSULT-II
Check continuity between terminals 3 and 5.
OK or NG
OK
>> GO TO 9.
NG
>> Replace fuel pump relay.
9.
CHECK FUEL PUMP
1.
Disconnect fuel pump harness connector.
2.
Check resistance between terminals 1 and 2.
OK or NG
OK
>> GO TO 10.
NG
>> Replace fuel pump.
10.
CHECK INTERMITTENT INCIDENT
Refer to
EC-696, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
>> INSPECTION END.
Removal and Installation
UBS00DQK
FUEL PUMP
Refer to
FL-6, "FUEL LEVEL SENSOR UNIT AND FUEL PUMP ASSEMBLY"
.
SEF073Y
Condition
Continuity
12V direct current supply between ter-
minals 1 and 2
Yes
No current supply
No
SEF511P
Resistance: 0.2 - 5.0
Ω [at 25°C (77°F)]
SEF022S
EC-1154
[VG33E]
POWER STEERING OIL PRESSURE SWITCH
POWER STEERING OIL PRESSURE SWITCH
PFP:49761
Component Description
UBS00DQL
The power steering oil pressure switch is attached to the power
steering high-pressure tube and detects a power steering load.
When a power steering load is detected, it signals the ECM. The
ECM adjusts the IACV-AAC valve to increase the idle speed and
adjust for the increased load.
CONSULT-II Reference Value in Data Monitor Mode
UBS00DQM
Specification data are reference values.
LEC521
MONITOR ITEM
CONDITION
SPECIFICATION
PW/ST SIGNAL
●
Engine: After warming up, idle the
engine
Steering wheel in neutral position
(forward direction)
OFF
The steering wheel is turned.
ON
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст