Nissan Frontier D22. Manual — part 319
DTC P0460 FUEL LEVEL SENSOR
EC-379
[KA24DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Diagnostic Procedure
UBS00D8F
1.
CHECK FUEL LEVEL SENSOR POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect fuel level sensor unit and fuel pump harness connector.
3.
Turn ignition switch ON.
4.
Check voltage between fuel level sensor unit and fuel pump ter-
minal 1 and ground with CONSULT-II or a tester.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 2.
2.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors M67, C1
●
Harness for open or short between combination meter and fuel level sensor until and fuel pump
>> Repair or replace harness or connectors.
3.
CHECK FUEL LEVEL SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Check harness continuity between fuel level sensor unit terminal 4 and body ground.
Refer to Wiring Diagram.
3.
Also check harness for short to power.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 4.
4.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors M67, C1
●
Harness for open or short between fuel level sensor and body ground
>> Repair open circuit or short to power in harness or connectors.
Voltage
: Battery voltage
SEF863Z
Continuity should exist.
EC-380
[KA24DE]
DTC P0460 FUEL LEVEL SENSOR
5.
CHECK FUEL LEVEL SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Disconnect ECM harness connector.
2.
Check harness continuity between ECM terminal 46 and fuel level sensor unit terminal 1, ECM terminal
66 and fuel level sensor unit terminal 4.
Refer to Wiring Diagram.
3.
Also check harness for short to power.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 6.
6.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors M81, F36
●
Harness connectors M67, C1
●
Harness for open or short between ECM and fuel level sensor
>> Repair open circuit or short to ground or short to power in harness or connectors.
7.
CHECK FUEL LEVEL SENSOR
DI-19, "VEHICLE SPEED SENSOR SIGNAL CHECK"
.
OK or NG
OK
>> GO TO 8.
NG
>> Replace fuel level sensor unit.
8.
CHECK INTERMITTENT INCIDENT
EC-120, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
>> INSPECTION END.
Removal and Installation
UBS00D8G
FUEL LEVEL SENSOR
FL-6, "FUEL LEVEL SENSOR UNIT AND FUEL PUMP ASSEMBLY"
.
Continuity should exist.
DTC P0461 FUEL LEVEL SENSOR
EC-381
[KA24DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P0461 FUEL LEVEL SENSOR
PFP:25060
Component Description
UBS00D8H
The fuel level sensor is mounted in the fuel level sensor unit. The
sensor detects a fuel level in the fuel tank and transmits a signal to
the ECM.
It consists of two parts, one is mechanical float and the other is vari-
able resistor. Fuel level sensor output voltage changes depending on
the movement of the fuel mechanical float.
On Board Diagnostic Logic
UBS00D8I
Driving long distances naturally affects fuel gauge level.
This diagnosis detects the fuel gauge malfunction of the gauge not moving even after a long distance has
been driven.
Malfunction is detected when the output signal of the fuel level sensor does not change within the specified
range even though the vehicle has been driven a long distance.
Overall Function Check
UBS00D8J
Use this procedure to check the overall function of the fuel level sensor function. During this check, a 1st trip
DTC might not be confirmed.
WARNING:
When performing following procedure, be sure to observe the handling of the fuel. Refer to
TESTING CONDITION:
Before starting overall function check, preparation of draining fuel and refilling fuel is required.
WITH CONSULT-II
NOTE:
Start from step 10, if it is possible to confirm that the fuel cannot be drained by 30 (7-7/8 US gal, 6-5/
8 Imp gal) in advance.
1.
Prepare a fuel container and a spare hose.
2.
Release fuel pressure from fuel line, refer to
EC-46, "FUEL PRESSURE RELEASE"
3.
Remove the fuel feed hose on the fuel level sensor unit.
4.
Connect a spare fuel hose where the fuel feed hose was removed.
5.
Turn ignition switch OFF and wait at least 10 seconds then turn ON.
6.
Select “FUEL LEVEL SE” in “DATA MONITOR” mode with CON-
SULT-II.
7.
Check “FUEL LEVEL SE” output voltage and note it.
8.
Select “FUEL PUMP” in “ACTIVE TEST” mode with CONSULT-
II.
9.
Touch “ON” and drain fuel approximately 30 (7-7/8 US gal, 6-
5/8 Imp gal) and stop it.
10. Check “FUEL LEVEL SE” output voltage and note it.
11. Fill fuel into the fuel tank for 30 (7-7/8 US gal, 6-5/8 Imp gal).
12. Check “FUEL LEVEL SE” output voltage and note it.
SEF725Z
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0461
0461
Fuel level sensor circuit
range/performance
The output signal of the fuel level sensor does
not change within the specified range even
though the vehicle has been driven a long dis-
tance.
●
Harness or connectors
(The sensor circuit is open or shorted)
●
Fuel level sensor
SEF195Y
EC-382
[KA24DE]
DTC P0461 FUEL LEVEL SENSOR
13. Confirm whether the voltage changes more than 0.03V during step 7 to 10 and 10 to 12.
If NG, check the fuel level sensor, refer to
DI-18, "FUEL LEVEL SENSOR UNIT CHECK"
WITH GST
NOTE:
Start from step 11, if it is possible to confirm that the fuel cannot be drained by 30 (7-7/8 US gal, 6-5/
8 Imp gal) in advance.
1.
Prepare a fuel container and a spare hose.
2.
Release fuel pressure from fuel line, refer to
EC-46, "FUEL PRESSURE RELEASE"
3.
Remove the fuel feed hose on the fuel level sensor unit.
4.
Connect a spare fuel hose where the fuel feed hose was removed.
5.
Turn ignition switch OFF.
6.
Set voltmeters probe between ECM terminal 46 (fuel level sen-
sor signal) and ground.
7.
Turn ignition switch ON.
8.
Check voltage between ECM terminal 46 and ground and note
it.
9.
Drain fuel by 30 (7-7/8 US gal, 6-5/8 Imp gal) from the fuel
tank using proper equipment.
10. Fill fuel into the fuel tank for 30 (7-7/8 US gal, 6-5/8 Imp gal).
11. Confirm that the voltage between ECM terminal 46 and ground
changes more than 0.03V during step 8 - 10.
If NG, check component of fuel level sensor, refer to
"FUEL LEVEL SENSOR UNIT CHECK"
SEF703Z
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст