Nissan Frontier D22. Manual — part 910
SRS-6
SRS CONFIGURATION
SRS CONFIGURATION
PFP:00000
Description
EHS000SS
The air bags and seat belt pre-tensioners deploy if the air bag diagnosis sensor unit activates while the ignition
switch is in the ON or START position.
The air bag diagnosis sensor unit will deploy the air bags and the seat belt pre-tensioners if the G sensor acti-
vates simultaneously with the safing sensor while the ignition switch is ON.
LHIA0018E
Ignition
Diagnosis sensor unit
Driver air bag
Passenger air bag
Driver seat belt
pre-tensioner
Passenger seat
belt pre-tensioner
G sensor
Safing sensor
ON
ON
ON
Deploy
ON
—
ON
Deploy
ON
ON
ON
Deploy
SRS CONFIGURATION
SRS-7
C
D
E
F
G
I
J
K
L
M
A
B
SRS
PASSENGER AIR BAG DEACTIVATION SWITCH (2-DOOR MODELS)
The vehicle (2-door models) is equipped with a passenger air bag deactivation switch which can be operated
by the customer. When the switch is turned to the ON position, the passenger air bag is enabled and could
inflate in a frontal collision. When the switch is turned to the OFF position, the passenger air bag is disabled
and will not inflate in a frontal collision.
After turning the ignition switch ON, the passenger air bag deactivation switch indicator on the instrument
panel illuminates for bulb check. The indicator will remain illuminated if the passenger air bag deactivation
switch is in the OFF position. If the passenger air bag deactivation switch is in the ON position, the indicator
will turn off after about 7 seconds.
After SRS maintenance or repair, make sure the passenger air bag
deactivation switch is in the same position (ON or OFF) as when the
vehicle arrived for service.
IGN OFF
→ ON
SRS Component Parts Location
EHS000ST
WRS260
Passenger air bag deactivation switch
position
Passenger air bag deactivation switch indi-
cator
Passenger air bag deployment
ON
Turns off within 7 seconds
Enabled
OFF
Remains illuminated
Disabled
LHIA0020E
SRS-8
SRS CONFIGURATION
Direct-connect SRS Component Connectors
EHS000SU
The following SRS components use direct-connect style harness connectors.
●
Driver air bag module
●
Front LH seat belt pre-tensioner
●
Front RH seat belt pre-tensioner
Always pull up to release black locking tab prior to removing connector from SRS component.
Always push down to lock black locking tab after installing connector
to SRS component.
WHIA0103E
TROUBLE DIAGNOSIS
SRS-9
C
D
E
F
G
I
J
K
L
M
A
B
SRS
TROUBLE DIAGNOSIS
PFP:00004
Trouble Diagnoses Introduction
EHS000SV
CAUTION:
●
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harness connec-
tors.
●
Do not attempt to repair, splice or modify the SRS wiring harness. If the harness is damaged,
replace it with a new one.
●
Keep ground portion clean.
DIAGNOSIS FUNCTION
The SRS self-diagnosis results can be read by using “AIR BAG” warning lamp and/or CONSULT-II. The read-
ing of these results is accomplished using one of two modes — “User mode” and “Diagnosis mode”.
The User mode is exclusively prepared for the customer (driver). This mode warns the driver of a system mal-
function through the operation of the “AIR BAG” warning lamp.
The Diagnosis mode allows the technician to locate and inspect the malfunctioning part.
The mode applications for the “AIR BAG” warning lamp and CONSULT-II are as follows:
NOTE:
Seat belt pre-tensioner malfunction is indicated by “AIR BAG” warning lamp.
DIAGNOSIS MODE FOR CONSULT-II
●
“SELF-DIAG [CURRENT]”
A current Self-diagnosis result (also indicated by the number of warning lamp flashes in the Diagnosis
mode) is displayed on the CONSULT-II screen in real time. This refers to a malfunctioning part requiring
repairs.
●
“SELF-DIAG [PAST]”
Diagnosis results previously stored in the memory are displayed on the CONSULT-II screen. The stored
results are not erased until memory erasing is executed.
●
“TROUBLE DIAG RECORD”
With TROUBLE DIAG RECORD, diagnosis results previously erased by a reset operation can be dis-
played on the CONSULT-II screen.
●
“ECU DISCRIMINATED NO.”
The diagnosis sensor unit for each vehicle model is assigned
with its own, individual classification number. This number will
be displayed on the CONSULT-II screen, as shown. When
replacing the diagnosis sensor unit, refer to the part number for
the compatibility. After installation, replacement with a correct
unit can be checked by confirming this classification number on
the CONSULT-II screen.
User mode
Diagnosis mode
Display type
“AIR BAG” warning lamp
X
X
ON-OFF operation
CONSULT-II
—
X
Monitoring
Model
ECU Part No.
ECU Discriminated No.
2-door 28556
8Z300
A60C
4-door
28556 8Z500
A60D
ARS366
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст