Nissan Frontier D22. Manual — part 824
MTC-18
LUBRICANT
Lubricant Adjusting Procedure for Components Replacement Except Compressor
After replacing any of the following major components, add the correct amount of lubricant to the system.
Amount of lubricant to be added
●
*1:
If compressor is replaced, addition of lubricant is included in the flow chart.
●
*2:
If refrigerant leak is small, no addition of lubricant is needed.
Lubricant Adjusting Procedure for Compressor Replacement
1.
Before connecting recovery/recycling equipment to vehicle, check recovery/recycling equipment gauges.
No refrigerant pressure should be displayed, recover refrigerant from equipment lines and then check
refrigerant purity.
2.
Confirm refrigerant purity in supply tank using recovery/recycling equipment and refrigerant identifier.
3.
Confirm refrigerant purity in vehicle A/C system using recovery/recycling equipment and refrigerant identi-
fier.
4.
Discharge refrigerant into the refrigerant recovery/recycling equipment. Measure lubricant discharged into
the recovery/recycling equipment.
5.
Drain the lubricant from the old (removed) compressor into a graduated container and record the amount
of lubricant drained.
6.
Drain the lubricant from the new compressor into a separate, clean container.
7.
Measure an amount of new lubricant installed equal to amount drained from old compressor. Add this
lubricant to new compressor through the suction port opening.
8.
Measure an amount of new lubricant equal to the amount recovered during discharging. Add this lubri-
cant to new compressor through the suction port opening.
9.
If the liquid tank also needs to be replaced, add an additional 5 m (0.2 US fl oz, 0.2 Imp fl oz) of lubricant
at this time.
Part replaced
Lubricant to be added to
system
Remarks
Amount of lubricant
m
(US fl oz, Imp fl oz)
Evaporator
75 (2.5, 2.6)
—
Condenser
75 (2.5, 2.6)
—
Liquid tank
5 (0.2, 0.2)
Add if compressor is not
replaced. *1
In case of refrigerant leak
30 (1.0, 1.1)
Large leak
—
Small leak *2
LUBRICANT
MTC-19
C
D
E
F
G
H
I
K
L
M
A
B
MTC
Do not add this 5 m (0.2 US fl oz, 0.2 Imp fl oz) of lubricant if only replacing the compressor.
RHA065DD
MTC-20
AIR CONDITIONER CONTROL
AIR CONDITIONER CONTROL
PFP:27500
Control Operation
EJS00200
FAN CONTROL KNOB
This knob turns the fan ON and OFF, and controls fan speed.
MODE CONTROL KNOB
This knob controls the direction of air flow through the front discharge outlets. The air conditioner compressor
turns on when the switch is turned to the defrost
or foot/defrost
position. It will remain on until the key
is turned off or the fan switch is turned off (it will remain off only while the fan is off).
TEMPERATURE CONTROL KNOB
This knob allows adjustment of the outlet air temperature.
RECIRCULATION (REC) SWITCH
OFF position: Outside air is drawn into the passenger compartment.
ON position: Interior air is recirculated inside the vehicle. The indicator lamp will also light.
AIR CONDITIONER SWITCH
The air conditioner switch controls the A/C system. When the switch is depressed with the fan ON, the A/C
relay is activated by the ECM allowing compressor operation. The indicator lamp will also light.
The air conditioner cooling function operates only when the engine is running and ambient air temper-
ature is above 2
°C (35°F).
REAR WINDOW DEFOGGER SWITCH (IF EQUIPPED)
OFF position: Rear window defogger is not operating.
ON position: Rear window defogger is operating.
WJIA0279E
AIR CONDITIONER CONTROL
MTC-21
C
D
E
F
G
H
I
K
L
M
A
B
MTC
Discharge Air Flow
EJS00201
*1
WJIA0280E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст