Nissan Frontier D22. Manual — part 91
DTC P1760 OVERRUN CLUTCH SOLENOID VALVE
AT-333
[RE4R01A]
D
E
F
G
H
I
J
K
L
M
A
B
AT
Component Inspection
ECS007NQ
OVERRUN CLUTCH SOLENOID VALVE
●
For removal, refer to
Resistance Check
●
Check resistance between terminal 4 and ground.
Operation Check
●
Check solenoid valve by listening for its operating sound while
applying battery voltage to the terminal 4 and ground.
SAT139K
Solenoid valve
Terminal No.
Resistance (Approx.)
Overrun clutch solenoid valve
4
Ground
20 - 40
Ω
SAT688I
AT-334
[RE4R01A]
DTC BATT/FLUID TEMP SEN (A/T FLUID TEMP SENSOR CIRCUIT AND TCM
POWER SOURCE)
DTC BATT/FLUID TEMP SEN (A/T FLUID TEMP SENSOR CIRCUIT AND TCM
POWER SOURCE)
PFP:31940
Description
ECS007NR
The A/T fluid temperature sensor detects the A/T fluid temperature
and sends a signal to the TCM.
CONSULT-II REFERENCE VALUE IN DATA MONITOR
MODE
Remarks: Specification data are reference values.
TCM TERMINALS AND REFERENCE VALUE
Remarks: Specification data are reference values.
SAT342HA
SAT021J
Monitor item
Condition
Specification (Approx.)
A/T fluid temperature
sensor
Cold [20
°C (68°F)]
↓
Hot [80
°C (176°F)]
1.5V
↓
0.5V
2.5k
Ω
↓
0.3k
Ω
Terminal
No.
Wire color
Item
Condition
Judgement stan-
dard (Approx.)
10
W/R
Power source
When turning ignition switch to ON.
Battery voltage
When turning ignition switch to OFF.
0V
19
W/R
Power source
(Same as No. 10)
When turning ignition switch to ON.
Battery voltage
When turning ignition switch to OFF.
0V
28
R/Y
Power source
(Memory back-
up)
or
When turning ignition switch to OFF.
Battery voltage
When turning ignition switch to ON.
Battery voltage
42
BR
Throttle position
sensor (Ground)
—
0V
47
R/B
A/T fluid temper-
ature sensor
When ATF temperature is 20
°C
(68
°F).
1.5V
When ATF temperature is 80
°C
(176
°F).
0.5V
DTC BATT/FLUID TEMP SEN (A/T FLUID TEMP SENSOR CIRCUIT AND TCM
POWER SOURCE)
AT-335
[RE4R01A]
D
E
F
G
H
I
J
K
L
M
A
B
AT
ON BOARD DIAGNOSIS LOGIC
DIAGNOSTIC TROUBLE CODE (DTC) CONFIRMATION
PROCEDURE
After the repair, perform the following procedure to confirm the mal-
function is eliminated.
With CONSULT-II
1.
Start engine.
2.
Select “DATA MONITOR” mode for “A/T” with CONSULT-II.
3.
Drive vehicle under the following conditions:
Selector lever in D position, vehicle speed higher than 20 km/h
(12 MPH).
Without CONSULT-II
●
Follow the procedure “With CONSULT-II”.
Diagnostic trouble code
Malfunction is detected when ...
Check item
(Possible cause)
: BATT/FLUID TEMP SEN
TCM receives an excessively low or high
voltage from the sensor.
●
Harness or connections
(The sensor circuit is open or shorted)
●
A/T fluid temperature sensor
: 8th judgement flicker
SAT014K
SAT971J
SAT335HB
AT-336
[RE4R01A]
DTC BATT/FLUID TEMP SEN (A/T FLUID TEMP SENSOR CIRCUIT AND TCM
POWER SOURCE)
Wiring Diagram — AT — BA/FTS
ECS007NS
WCWA0155E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст