Nissan Frontier D22. Manual — part 572
DTC P0133, P0153 HO2S1
EC-1391
[VG33ER]
C
D
E
F
G
H
I
J
K
L
M
A
EC
3.
CHECK FOR EXHAUST GAS LEAK
1.
Start engine and run it at idle.
2.
Listen for an exhaust gas leak before three way catalyst (manifold).
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace.
4.
CHECK FOR INTAKE AIR LEAK
Listen for an intake air leak after the mass air flow sensor.
OK or NG
OK
>> GO TO 5.
NG
>> Repair or replace.
SEC502D
EC-1392
[VG33ER]
DTC P0133, P0153 HO2S1
5.
CLEAR THE SELF-LEARNING DATA
With CONSULT-II
1.
Start engine and warm it up to normal operating temperature.
2.
Select “SELF-LEARNING CONT” in “WORK SUPPORT” mode
with CONSULT-II.
3.
Clear the self-learning control coefficient by touching “CLEAR”.
4.
Run engine for at least 10 minutes at idle speed.
Is the 1st trip DTC P0171, P0172, P0174 or P0175 detected?
Is it difficult to start engine?
Without CONSULT-II
1.
Start engine and warm it up to normal operating temperature.
2.
Turn ignition switch OFF.
3.
Disconnect mass air flow sensor harness connector, and restart and run engine for at least 5 seconds at
idle speed.
4.
Stop engine and reconnect mass air flow sensor harness connector.
5.
Make sure DTC P0102 is displayed.
6.
Erase the DTC memory. Refer to
EC-1233, "HOW TO ERASE EMISSION-RELATED DIAGNOSTIC
.
7.
Make sure DTC P0000 is displayed.
8.
Run engine for at least 10 minutes at idle speed.
Is the 1st trip DTC P0171, P0172, P0174 or P0175 detected?
Is it difficult to start engine?
Yes or No
Yes
>> Perform trouble diagnosis for DTC P0171, P0174 or P0172, P0175. Refer to
.
No
>> GO TO 6.
SEF968Y
DTC P0133, P0153 HO2S1
EC-1393
[VG33ER]
C
D
E
F
G
H
I
J
K
L
M
A
EC
6.
CHECK HO2S1 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Check heated oxygen sensor 1 harness protector.
3.
Disconnect corresponding heated oxygen sensor 1 harness
connector.
4.
Disconnect ECM harness connector.
5.
Check harness continuity between ECM terminal and HO2S1
terminal as follows.
Refer to Wiring Diagram.
6.
Check harness continuity between ECM terminal or HO2S1 terminal and ground as follows.
Refer to Wiring Diagram.
7.
Also check harness for short to power.
OK or NG
OK
>> GO TO 7.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
7.
CHECK MASS AIR FLOW SENSOR
Refer to
EC-1333, "Component Inspection"
OK or NG
OK
>> GO TO 8.
NG
>> Replace mass air flow sensor.
PBIB0636E
DTC
Terminals
Bank
ECM
Sensor
P0133
50
2
Bank 1
P0153
51
2
Bank 2
Continuity should exist.
DTC
Terminals
Bank
ECM or sensor
Ground
P0133
50 or 2
Ground
Bank 1
P0153
51 or 2
Ground
Bank 2
Continuity should not exist.
BBIA0189E
EC-1394
[VG33ER]
DTC P0133, P0153 HO2S1
8.
CHECK PCV VALVE
With engine running at idle, remove PCV valve from rocker cover;
make sure that a hissing noise will be heard as air passes through it
and a strong vacuum should be felt immediately when a finger is
placed over valve inlet.
OK or NG
OK (With CONSULT-II)>> GO TO 9.
OK (Without CONSULT-II)>>GO TO 10.
NG
>> Replace PCV valve.
SEC137A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст