Nissan Frontier D22. Manual — part 705
SUPERCHARGER
EM-127
[VG33E and VG33ER]
C
D
E
F
G
H
I
J
K
L
M
A
EM
2.
Check the supercharger bypass valve actuator rod for smooth movement while maintaining the pressure
at the specified levels below:
Installation
EBS00GTU
Installation is in the reverse order of removal.
●
Replace all gaskets; make sure that all gasket surfaces are clean and undamaged.
●
Follow all torque sequences for tightening nuts and bolts.
●
Refill the cooling system. Refer to
MA-26, "REFILLING ENGINE COOLANT"
Rod starts to extend at approximately
: 12 kPa (90 mmHg, 3.54 inHg)
Rod is fully extended at approximately
: 33.3 kPa (250 mmHg, 9.84 inHg)
Rod full extended length
: 20.83 - 22.71 mm (0.82 - 0.89 in)
EM-128
[VG33E and VG33ER]
ENGINE ASSEMBLY
ENGINE ASSEMBLY
PFP:10001
Removal and Installation
EBS00GTV
Engine Mounting
AEM471
ENGINE ASSEMBLY
EM-129
[VG33E and VG33ER]
C
D
E
F
G
H
I
J
K
L
M
A
EM
WARNING:
●
Place the vehicle on a flat and solid surface.
●
Place wheel chocks at the front and back of the rear wheels.
●
Do not remove the engine until the exhaust system has completely cooled off. Otherwise, you may
burn yourself and/or fire may break out in the fuel line.
●
For safety, the tension of wires should be loosened against the engine.
●
Before disconnecting a fuel hose, release the fuel pressure from the fuel line. Refer to
EC-1218, "FUEL PRESSURE RELEASE"
●
Before removing the front axle from the transmission, place safety stands under the designated
front supporting points. Refer to
.
●
Raise the engine and transmission in a safe manner.
●
For engines not equipped with engine slingers, attach the appropriate slingers and bolts as
described in the PARTS CATALOG.
CAUTION:
●
When lifting engine, be careful not to strike adjacent parts, especially accelerator wire casing,
brake lines, and brake master cylinder.
●
In hoisting the engine, always use engine slingers in a safe manner.
●
Before separating engine and transmission, remove crankshaft position sensor (OBD) from the
assembly.
●
Always take extra care not to damage edge of crankshaft position sensor (OBD), or ring gear
teeth.
●
Do not loosen front engine mounting insulator cover
mounting nuts. When cover is removed, damper oil flows
out and mounting insulator will not function.
●
Tighten all bolts and nuts to specification.
REMOVAL
1.
Remove the engine undercover and hood. Refer to
EI-12, "Removal and Installation"
2.
Drain the coolant from the cylinder block and radiator. Refer to
MA-26, "DRAINING ENGINE COOLANT"
.
SEM322F
WEM064
EM-130
[VG33E and VG33ER]
ENGINE ASSEMBLY
3.
Before disconnecting fuel hose, release the fuel pressure from the fuel line. Refer to
(VG33E),
EC-1218, "FUEL PRESSURE RELEASE"
4.
Disconnect the vacuum hoses, fuel tubes, wires, harnesses and connectors.
5.
Remove the radiator with shroud and cooling fan. Refer to
CO-30, "Removal and Installation"
6.
Remove the drive belts. Refer to
7.
Discharge the A/C system refrigerant. Refer to
MTC-64, "HFC-134a (R-134a) Service Procedure"
.
8.
Remove the A/C compressor manifold. Refer to
9.
Remove the power steering oil pump from the engine. Refer to
10. Remove the front exhaust tubes. Refer to
EX-3, "Removal and Installation"
.
11. Remove the transmission from the vehicle. Refer to
AT-62, "REMOVAL AND INSTALLATION"
(RL4R01A),
AT-407, "REMOVAL AND INSTALLATION"
MT-10, "Removal and Installation"
(FS5W71C),
MT-48, "Removal and Installation"
(FS5R30A).
12. Install the engine slingers.
13. Raise the engine slightly with the engine slingers and then remove the engine mounting nuts from both
sides.
14. Lift and remove the engine from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
Slinger bolts
: 20
− 26 N·m (2.1 − 2.7 kg−m,
15
− 20 ft−lb)
SEM323F
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст