Nissan Frontier D22. Manual — part 492
DTC P1444 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
EC-1071
[VG33E]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than the ECM terminals, such as the ground.
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
4
OR/B
ECM relay (Self shut-
off)
[Engine is running]
[Ignition switch: OFF]
●
For a few seconds after turning ignition switch
OFF
0 - 1.5V
[Ignition switch: OFF]
●
A few seconds passed after turning ignition
switch OFF
BATTERY VOLTAGE
(11 - 14V)
5
R/Y
EVAP canister purge
volume control solenoid
valve
[Engine is running]
●
Idle speed
BATTERY VOLTAGE
(11 - 14V)
[Engine is running]
●
Engine speed is 2,000 rpm
(More than 100 seconds after starting engine)
BATTERY VOLTAGE
(11 - 14V)
67
B/P
Power supply for ECM
[Ignition switch: ON]
BATTERY VOLTAGE
(11 - 14V)
72
B/P
117
B/P
Current return
[Engine is running]
●
Idle speed
BATTERY VOLTAGE
(11 - 14V)
SEF994U
SEF995U
EC-1072
[VG33E]
DTC P1444 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
Diagnostic Procedure
UBS00DOR
1.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE POWER SUPPLY CIR-
CUIT
1.
Turn ignition switch OFF.
2.
Disconnect EVAP canister purge volume control solenoid valve
harness connector.
3.
Turn ignition switch ON.
4.
Check voltage between terminal 1 and engine ground with CON-
SULT-II or tester.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 2.
2.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors F36, M81
●
Harness connectors M65, E43
●
Harness for open or short between EVAP canister purge volume control solenoid valve and ECM relay
●
Harness for open or short between EVAP canister purge volume control solenoid valve and ECM
>> Repair harness or connectors.
3.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OUTPUT SIGNAL CIR-
CUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between ECM terminal 5 and EVAP canister purge volume control solenoid
valve terminal 2. Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 4.
AEC652A
Voltage: Battery voltage
SEF646W
Continuity should exist.
DTC P1444 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
EC-1073
[VG33E]
C
D
E
F
G
H
I
J
K
L
M
A
EC
4.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors E43, M65
●
Harness connectors M81, F36
●
Harness for open or short between EVAP canister purge volume control solenoid valve and ECM
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR HOSE
Check disconnection or improper connection of hose connected to EVAP control system pressure sensor.
OK or NG
OK
>> GO TO 6.
NG
>> Repair it.
6.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR CONNECTOR
1.
Disconnect EVAP control system pressure sensor harness con-
nector.
2.
Check connectors for water.
Water should not exist.
OK or NG
OK
>> GO TO 7.
NG
>> Replace EVAP control system pressure sensor.
7.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
1.
Remove EVAP control system pressure sensor with its harness connector connected.
2.
Remove hose from EVAP control system pressure sensor.
3.
Turn ignition switch ON.
4.
Use pump to apply vacuum and pressure to EVAP control system pressure sensor as shown in figure.
5.
Check input voltage between ECM terminal 62 and ground.
CAUTION:
●
Always calibrate the vacuum pump gauge when using it.
●
Do not apply below
−93.3 kPa (−700 mmHg, −27.56 inHg) or
over 101.3 kPa (760 mmHg, 29.92 inHg) of pressure.
OK or NG
OK (with CONSULT-II)>>GO TO 8.
OK (without CONSULT-II)>>GO TO 9.
NG
>> Replace EVAP control system pressure sensor.
AEC651A
Applied vacuum
Voltage V
Not applied
1.4 - 4.8
-26.7 kpa (-200 mmHg, -7.87 inHg)
2.1 to 2.5V lower than above value
PBIB1426E
EC-1074
[VG33E]
DTC P1444 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
8.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
With CONSULT-II
1.
Start engine.
2.
Perform “PURG VOL CONT/V” in “ACTIVE TEST” mode with
CONSULT-II. Check that engine speed varies according to the
valve opening.
If OK, inspection end. If NG, go to following step.
3.
Check air passage continuity.
If NG, replace the EVAP canister purge volume control solenoid
valve.
OK or NG
OK
>> GO TO 10.
NG
>> Replace EVAP canister purge volume control solenoid
valve.
9.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
Without CONSULT-II
Check air passage continuity.
If NG, replace the EVAP canister purge volume control solenoid
valve.
OK or NG
OK
>> GO TO 10.
NG
>> Replace EVAP canister purge volume control solenoid
valve.
SEF985Y
Condition
PURG VOL CONT/V value
Air passage continuity
between A and B
100%
Yes
0%
No
SEF660U
Condition
Air passage continuity
between A and B
12V direct current supply between
terminals 1 and 2
Yes
No supply
No
SEF661U
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст