Nissan Frontier D22. Manual — part 546
TROUBLE DIAGNOSIS
EC-1287
[VG33ER]
C
D
E
F
G
H
I
J
K
L
M
A
EC
FUNCTION
INSPECTION PROCEDURE
1.
Turn ignition switch OFF.
2.
Connect “GST” to data link connector which is located under LH
dash panel near the fuse box cover.
Diagnostic test mode
Function
MODE 1
READINESS TESTS
This mode gains access to current emission-related data values, including analog inputs
and outputs, digital inputs and outputs, and system status information.
MODE 2
(FREEZE DATA)
This mode gains access to emission-related data value which were stored by ECM during
the freeze frame. For details, refer to
EC-1279, "Freeze Frame Data and 1st Trip Freeze
.
MODE 3
DTCs
This mode gains access to emission-related power train trouble codes which were stored
by ECM.
MODE 4
CLEAR DIAG INFO
This mode can clear all emission-related diagnostic information. This includes:
●
Clear number of diagnostic trouble codes (MODE 1)
●
Clear diagnostic trouble codes (MODE 3)
●
Clear trouble code for freeze frame data (MODE 1)
●
Clear freeze frame data (MODE 2)
●
Reset status of system monitoring test (MODE 1)
●
Clear on board monitoring test results (MODE 6 and 7)
MODE 6
(ON BOARD TESTS)
This mode accesses the results of on board diagnostic monitoring tests of specific com-
ponents/systems that are not continuously monitored.
MODE 7
(ON BOARD TESTS)
This mode enables the off board test drive to obtain test results for emission-related pow-
ertrain components/systems that are continuously monitored during normal driving condi-
tions.
MODE 8
—
This mode can close EVAP system in ignition switch ON position (Engine stopped).
When this mode is performed, EVAP canister vent control valve: Closed, bypass valve:
Open.
In the following conditions, this mode cannot function.
●
Low ambient temperature
●
Low battery voltage
●
Engine running
●
Ignition switch OFF
●
Low fuel temperature
●
Too much pressure is applied to EVAP system
MODE 9
CALIBRATION ID
This mode is to enable the off-board to request vehicle specific vehicle information such
as Vehicle Identification Number (VIN) and calibration IDs.
LEC104A
EC-1288
[VG33ER]
TROUBLE DIAGNOSIS
3.
Turn ignition switch ON.
4.
Enter the program according to instruction on the screen or in
the operation manual.
(*: Regarding GST screens in this section, sample screens are
shown.)
5.
Perform each diagnostic mode according to each service proce-
dure.
For further information, see the GST Operation Manual of the
tool maker.
CONSULT-II Reference Value in Data Monitor Mode
UBS00DSE
Remarks:
● Specification data are reference values.
● Specification data are output/input values which are detected or supplied by the ECM at the connector.
* Specification data may not be directly related to their components signals/values/operations.
i.e. Adjust ignition timing with a timing light before monitoring IGN TIMING, because the monitor may show the specification data in
spite of the ignition timing not being adjusted to the specification data. This IGN TIMING monitors the data calculated by the ECM
according to the signals input from the camshaft position sensor and other ignition timing related sensors.
AEC059B
AEC060B
MONITOR ITEM
CONDITION
SPECIFICATION
ENG SPEED
●
Run engine and compare CONSULT-II value with the tachometer indica-
tion.
Almost the same speed as the
tachometer indication.
MAS A/F SE-B1
●
Engine: After warming up
●
Air conditioner switch: OFF
●
Shift lever: N (A/T), Neutral (M/T)
●
No load
Idle
1.0 - 1.7V
2,500 rpm
1.7 - 2.3V
COOLAN TEMP/S
●
Engine: After warming up
More than 70
°C (158°F)
HO2S1 (B1)
HO2S1 (B2)
●
Engine: After warming up
Maintaining engine speed at 2,000
rpm.
0 - 0.3V
←→ Approx. 0.6 -
1.0V
HO2S1 MNTR (B1)
HO2S1 MNTR (B2)
LEAN
←→ RICH
Changes more than 5 times
during 10 seconds.
HO2S2 (B1)
HO2S2 (B2)
●
Warm-up condition
●
After keeping engine speed
between 3,500 and 4,000 rpm for
1 minute and at idle for 1 minute
under no load.
Revving engine from idle up to 3,000
rpm quickly
0 - 0.3V
←→ Approx. 0.6 -
1.0V
HO2S2 MNTR (B1)
HO2S2 MNTR (B2)
LEAN
←→ RICH
VHCL SPEED SE
●
Turn drive wheels and compare CONSULT-II value speedometer indica-
tion with the speedometer indication.
Almost the same speed as the
speedometer indication
BATTERY VOLT
●
Ignition switch: ON (Engine stopped)
11 - 14V
THRTL POS SEN
●
Engine: After warming up, idle
the engine
Throttle valve: fully closed
0.15 - 0.85V
●
Engine: After warming up
●
Ignition switch: ON
(Engine stopped)
Throttle valve: fully opened
3.5 - 4.7V
TROUBLE DIAGNOSIS
EC-1289
[VG33ER]
C
D
E
F
G
H
I
J
K
L
M
A
EC
START SIGNAL
●
Ignition switch: ON
→ START → ON
OFF
→ ON → OFF
CLSD THL POS
CLSD THL/P SW
●
Engine: After warming up, idle
the engine
Throttle valve: Idle position
ON
Throttle valve: Slightly open
OFF
AIR COND SIG
●
Engine: After warming up, idle
the engine
Air conditioner switch: OFF
OFF
Air conditioner switch: ON
(Compressor operates.)
ON
P/N POSI SW
●
Ignition switch: ON
Shift lever: P or N (A/T), Neutral (M/T)
ON
Except above
OFF
PW/ST SIGNAL
●
Engine: After warming up, idle
the engine
Steering wheel in neutral position
(forward direction)
OFF
The steering wheel is turned
ON
AMB TEMP SW
●
Ignition switch: ON
●
Compare ambient air tempera-
ture with the following:
Below 19
°C (66°F)
OFF
Above 25
°C (77°F)
ON
IGNITION SW
●
Ignition switch: ON
→ OFF → ON
ON
→ OFF → ON
INJ PULSE-B1
INJ PULSE-B2
●
Engine: After warming up
●
Air conditioner switch: OFF
●
Shift lever: N (A/T), Neutral (M/T)
●
No load
Idle
2.4 - 3.7 msec
2,000 rpm
1.9 - 3.3 msec
B/FUEL SCHDL
●
Engine: After warming up
●
Air conditioner switch: OFF
●
Shift lever: N (A/T), Neutral (M/T)
●
No load
Idle
1.0 - 1.6 msec
2,000 rpm
0.7 - 1.4 msec
IGN TIMING
●
Engine: After warming up
●
Air conditioner switch: OFF
●
Shift lever: N (A/T), Neutral (M/T)
●
No load
Idle
10
°±2° BTDC
2,000 rpm
More than 25
° BTDC
IACV-AAC/V
●
Engine: After warming up
●
Air conditioner switch: OFF
●
Shift lever: N (A/T), Neutral (M/T)
●
No load
Idle
10 - 20%
2,000 rpm
—
PURG VOL C/V
●
Engine: After warming up
●
Air conditioner switch: OFF
●
Shift lever: N (A/T), Neutral (M/T)
●
No load
Idle
0%
2,000 rpm
—
A/F ALPHA-B1
A/F ALPHA-B2
●
Engine: After warming up
Maintaining engine speed at 2,000
rpm
54 - 155%
EVAP SYS PRES
●
Ignition switch: ON
1.8 – 4.8V
AIR COND RLY
●
Air conditioner switch: OFF
→ ON
OFF
→ ON
FUEL PUMP RLY
●
Ignition switch is turned to ON (Operates for 5 seconds)
●
Engine running or cranking
ON
Except as shown above
OFF
VENT CONT/V
●
Ignition switch: ON
OFF
HO2S1 HTR (B1)
HO2S1 HTR (B2)
●
Engine speed: Below 2,800 rpm
ON
●
Engine speed: Above 2,800 rpm
OFF
MONITOR ITEM
CONDITION
SPECIFICATION
EC-1290
[VG33ER]
TROUBLE DIAGNOSIS
Major Sensor Reference Graph in Data Monitor Mode
UBS00DSF
The following are the major sensor reference graphs in “DATA MONITOR” mode.
THRTL POS SEN, ABSOL TH·P/S, CLSD THL POS
Below is the data for “THRTL POS SEN”, “ABSOL TH·P/S” and “CLSD THL POS” when depressing the accel-
erator pedal with the ignition switch ON.
The signal of “THRTL POS SEN” and “ABSOL TH·P/S” should rise gradually without any intermittent drop or
rise after “CLSD THL POS” is changed from “ON” to “OFF”.
ENG SPEED, MAS A/F SE-B1, THRTL POS SEN, HO2S2 (B1), HO2S1 (B1), INJ PULSE-B1
Below is the data for “ENG SPEED”, “MAS A/F SE-B1”, “THRTL POS SEN”, “HO2S2 (B1)”, “HO2S1 (B1)” and
“INJ PULSE-B1” when revving engine quickly up to 4,800 rpm under no load after warming up engine suffi-
ciently.
HO2S2 HTR (B1)
HO2S2 HTR (B2)
●
Engine speed: Below 3,600 rpm after the following conditions are met.
●
Engine: After warning up
●
Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute and
at idle for 1 minute under no load.
ON
●
Engine speed: Above 3,600 rpm
OFF
SCB/V CON S/V
●
More than 5 seconds after turning ignition switch ON (Engine stopped)
OFF
●
Engine speed: Idle
ON
VC/V BYPASS/V
Ignition switch: ON
OFF
CAL/LD VALUE
●
Engine: After warming up
●
Air conditioner switch: OFF
●
Shift lever: N (A/T), Neutral (M/T)
●
No load
Idle
18.5 - 26.0%
2,500 rpm
18.0 - 21.0%
ABSOL TH·P/S
●
Engine: After warming up
●
Ignition switch: ON
●
More than -40.0 kpa (-300
mmHg, -11.81 inHg) of vacuum is
applied to the throttle opener with
a hand vacuum pump.
Throttle valve: fully closed
0.0%
●
Engine: After warming up
●
Ignition switch: ON
(Engine stopped)
Throttle valve: fully opened
Approx. 80%
MASS AIRFLOW
●
Engine: After warming up
●
Air conditioner switch: OFF
●
Shift lever: N (A/T), Neutral (M/T)
●
No load
Idle
3.3 - 4.8 g·m/s
2,500 rpm
12.0 - 14.9 g·m/s
MONITOR ITEM
CONDITION
SPECIFICATION
SEF306Y
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст