Nissan Rogue. Manual — part 55
AV-212
< REMOVAL AND INSTALLATION >
[NAVIGATION WITHOUT BOSE]
GPS ANTENNA
GPS ANTENNA
Removal and Installation
INFOID:0000000011276899
REMOVAL
1. Remove instrument panel. Refer to
IP-14, "INSTRUMENT PANEL ASSEMBLY : Removal and Installa-
2. Remove screw and the GPS antenna.
INSTALLATION
Installation is in the reverse order of removal.
AV
ANTENNA BASE
AV-213
< REMOVAL AND INSTALLATION >
[NAVIGATION WITHOUT BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
ANTENNA BASE
Exploded View
INFOID:0000000011373314
Removal and Installation
INFOID:0000000011276900
REMOVAL
1. Remove the luggage side upper finisher (RH). Refer to
INT-36, "LUGGAGE SIDE UPPER FINISHER :
.
2. Partially lower headlining (rear). Refer to
INT-30, "Removal and Installation"
3. Disconnect harness connectors from antenna feeder.
4. Remove nut from antenna base and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
If the antenna base nut is not properly tightened, lower sensitivity of the antenna may be experienced.
If the nut is over tightened, this will deform the roof panel.
Disassembly and Assembly
INFOID:0000000011373316
DISASSEMBLY
Insert a suitable tool into gaps between antenna base (2) and the
cover (1), then remove the cover (1) from antenna base (2).
ASSEMBLY
Assembly is in the reverse order of disassembly.
AWNIA3705ZZ
1. Antenna rod
2. Antenna base
A. Antenna nut
ALNIA1335ZZ
AV-214
< REMOVAL AND INSTALLATION >
[NAVIGATION WITHOUT BOSE]
ANTENNA FEEDER
ANTENNA FEEDER
Feeder Layout
INFOID:0000000011276901
ANTENNA FEEDER LAYOUT
1.
Antenna base (antenna amp. and
satellite antenna)
2.
Rod Antenna
3.
M503
4.
M502
5.
M130, M501
6.
M129, M500
7.
M142
8.
M139
ALNIA1595ZZ
AV
PRECAUTIONS
AV-215
< PRECAUTION >
[NAVIGATION WITH BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000011345937
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Cautions in Removing Battery Terminal and AV Control Unit (Models with AV Control
Unit)
INFOID:0000000011276903
CAUTION:
Remove battery terminal and AV control unit 30 seconds or more after turning the ignition switch OFF.
NOTE:
After the ignition switch is turned OFF, the AV control unit continues operating for approximately 30 seconds.
Therefore, data corruption may occur if battery voltage is cut off within 30 seconds.
Precaution for Trouble Diagnosis
INFOID:0000000011276904
AV COMMUNICATION SYSTEM
• Do not apply voltage of 7.0 V or higher to the measurement terminals.
• Use the tester with its open terminal voltage being 7.0 V or less.
• Be sure to turn ignition switch OFF and disconnect the battery cable from the negative terminal before
checking the circuit.
Precaution for Harness Repair
INFOID:0000000011276905
AV COMMUNICATION SYSTEM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст