Nissan Rogue. Manual — part 836
LAN
CAN SYSTEM
LAN-43
< WIRING DIAGRAM >
[CAN]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
AAMIA2817GB
LAN-44
< BASIC INSPECTION >
[CAN]
DIAGNOSIS AND REPAIR WORKFLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Interview Sheet
INFOID:0000000011277522
SKIB8898E
LAN
MALFUNCTION AREA CHART
LAN-45
< DTC/CIRCUIT DIAGNOSIS >
[CAN]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
DTC/CIRCUIT DIAGNOSIS
MALFUNCTION AREA CHART
Main Line
INFOID:0000000011277523
Branch Line
INFOID:0000000011277524
Short Circuit
INFOID:0000000011277525
Malfunction area
Reference
Main line between IPDM E/R and data link connector
Main line between data link connector and chassis control module
Main line between chassis control module and automatic back
door control module
Main line between chassis control module and AWD control unit
Malfunction area
Reference
ECM branch line circuit
ABS actuator and electric unit (control unit) branch line circuit
IPDM E/R branch line circuit
TCM branch line circuit
Data link connector branch line circuit
Combination meter branch line circuit
Air bag diagnosis sensor unit branch line circuit
Chassis control module branch line circuit
EPS control unit branch line circuit
Steering angle sensor branch line circuit
AWD control unit branch line circuit
Automatic back door control module branch line circuit
BCM branch line circuit
AV control unit branch line circuit
Around view monitor control unit branch line circuit
A/C auto amp. branch line circuit
Front air control branch line circuit
Distance sensor branch line circuit
Malfunction area
Reference
CAN communication circuit 1
CAN communication circuit 2
LAN-46
< DTC/CIRCUIT DIAGNOSIS >
[CAN]
MAIN LINE BETWEEN IPDM-E AND DLC CIRCUIT
MAIN LINE BETWEEN IPDM-E AND DLC CIRCUIT
Diagnosis Procedure
INFOID:0000000011277526
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the following terminals and connectors for damage, bend and loose connection (connector side
and harness side).
-
Harness connector E152
-
Harness connector M31
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1. Disconnect the following harness connectors.
-
IPDM E/R
-
Harness connectors E152 and M31
2. Check the continuity between the IPDM E/R harness connector and the harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair the main line between the IPDM E/R and the harness connector E152.
3.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
Check the continuity between the harness connector and the data link connector.
Is the inspection result normal?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the IPDM E/R and the data link connector.
NO
>> Repair the main line between the harness connector M31 and the data link connector.
IPDM E/R harness connector
Harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
E120
24
E152
61J
Existed
22
60J
Existed
Harness connector
Data link connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
M31
61J
M22
6
Existed
60J
14
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст