Nissan Rogue. Manual — part 686
FRONT DRIVE SHAFT
FAX-37
< UNIT DISASSEMBLY AND ASSEMBLY >
[FWD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
4. Install dust shields.
CAUTION:
Do not reuse dust shields.
Wheel Side
1. Insert the amount of Genuine NISSAN Grease into joint sub-
assembly serration (1) hole until grease begins to ooze from ball
groove and serration hole.
CAUTION:
After inserting the grease, use a paper shop cloth to wipe
off old grease that has oozed out.
NOTE:
Always check with the Parts Department for the latest parts
information.
2. Install new boot and new small boot band onto shaft.
CAUTION:
• Do not reuse boot and boot bands.
• Cover drive shaft serration with protective tape (A) to pre-
vent damage to boot during installation.
3. Remove protective tape wound around serrated part of shaft.
4. Attach new circlip to shaft. The circlip must fit securely into shaft
groove. Attach nut to joint sub-assembly.
Use a suitable tool to press-fit.
CAUTION:
Do not reuse circlip.
5. Insert the amount of new Genuine NISSAN Grease listed below into housing from large end of boot.
NOTE:
Always check with the Parts Department for the latest parts information.
JPDIF0127ZZ
JPDIF0008ZZ
JPDIF0009ZZ
RAC0049D
Grease quantity
: Refer to
.
FAX-38
< UNIT DISASSEMBLY AND ASSEMBLY >
[FWD]
FRONT DRIVE SHAFT
6. Install boot securely into grooves (indicated by * marks) as
shown.
CAUTION:
If there is grease on boot mounting surfaces (indicated by *
marks) of shaft and housing, boot may come off. Remove
all grease from surfaces.
7. Make sure boot installation length (L) is the specified length.
Insert a suitable tool into the large end of boot. Bleed air from
boot to prevent boot deformation.
CAUTION:
• Boot may break if boot installation length is less than standard value.
• Be careful that suitable tool does not contact inside surface of boot.
8. Install new large and small boot bands securely using Tool.
CAUTION:
Do not reuse boot bands.
9. Secure boot band so that dimension (M) meets specification as
shown.
10. After installing housing and shaft, rotate boot to check whether or not the actual position is correct. If boot
position is not correct, remove old boot bands then reposition the boot and secure with new boot bands.
Boot installation length (L) : Refer to
Tool number
: KV40107300 (
—
)
JPDIF0222ZZ
RAC1133D
Dimension (M)
: Refer to
DSF0047D
SERVICE DATA AND SPECIFICATIONS (SDS)
FAX-39
< SERVICE DATA AND SPECIFICATIONS (SDS)
[FWD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000011278638
Drive Shaft
INFOID:0000000011278639
Drive Shaft Specifications
*Always check with the Parts Department for the latest parts information.
Dynamic Damper Specifications
Unit: mm (in)
Boot Band Specification
Item
Standard
Axial end play
0.0 mm (0.0 in)
Application
FWD
Joint type
Wheel side
Transaxle side
(LH)
(RH)
(LH)
(RH)
Grease quantity*
125
± 10 g
(4.41
± 0.35 oz)
185
± 10 g
(6.52
± 0.35 oz)
Boot installed length (L)
141.5 mm (5.57 in)
176.9 mm (6.96 in)
ALDIA0269ZZ
ALDIA0268ZZ
Application
FWD
(LH)
(RH)
Dimension (A)
243
± 3 (9.57 ± 0.12)
243
± 3 (9.57 ± 0.12)
Dimension (B)
70 (2.76)
50 (1.97)
ALDIA0270ZZ
FAX-40
< SERVICE DATA AND SPECIFICATIONS (SDS)
[FWD]
SERVICE DATA AND SPECIFICATIONS (SDS)
Unit: mm (in)
Dimension (M)
1.0 - 4.0 mm (0.039 - 0.157 in)
DSF0047D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст