Nissan Rogue. Manual — part 1156
STR-18
< DTC/CIRCUIT DIAGNOSIS >
B TERMINAL CIRCUIT
YES
>> “B” terminal circuit is OK. Further inspection is necessary. Refer to
STR-15, "Work Flow (Without GR8-1200 NI)"
.
NO
>> Check the starter motor case to engine mounting for high resistance.
S CONNECTOR CIRCUIT
STR-19
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
A
STR
N
P
O
S CONNECTOR CIRCUIT
Description
INFOID:0000000011279740
The starter motor magnetic switch is supplied with power when the ignition switch is turned to the START posi-
tion while the selector lever is in the P (Park) or N (Neutral) position.
Diagnosis Procedure
INFOID:0000000011279741
Regarding Wiring Diagram information, refer to
.
CAUTION:
Perform diagnosis under the condition that engine cannot start by the following procedure.
1. Remove fuel pump fuse.
2. Crank or start the engine (where possible) until the fuel pressure is released.
1.
CHECK “S” CONNECTOR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect starter motor connector.
3. Shift selector lever to “P” (Park) or “N” (Neutral) position.
4. Check voltage between starter motor harness connector and ground.
Is the inspection result normal?
YES
>> “S” circuit is OK. Further inspection is necessary. Refer to
STR-11, "Work Flow (With GR8-1200
STR-15, "Work Flow (Without GR8-1200 NI)"
.
NO
>> GO TO 2.
2.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1. Disconnect IPDM E/R connector.
2. Check continuity between starter motor harness connector and the IPDM E/R harness connector.
3. Check continuity between starter motor terminal S and ground.
Is the inspection result normal?
YES
>> Further inspection is necessary. Refer to
STR-11, "Work Flow (With GR8-1200 NI)"
"Work Flow (Without GR8-1200 NI)"
.
NO
>> Repair or replace the harness or connectors.
(+)
(-)
Condition
Voltage
(Approx.)
Connector Terminal
F34
S
Ground
When the ignition switch is in START position
Battery voltage
Starter motor harness connector
IPDM E/R harness connector
Continuity
Connector
Terminal
Connector
Terminal
F34
S
F41
83
Yes
Connector Terminal
—
Continuity
F34
S
Ground
No
STR-20
< SYMPTOM DIAGNOSIS >
STARTING SYSTEM
SYMPTOM DIAGNOSIS
STARTING SYSTEM
Symptom Table
INFOID:0000000011279742
Symptom
Reference
No normal cranking
Refer to
STR-11, "Work Flow (With GR8-1200 NI)"
or
"Work Flow (Without GR8-1200 NI)"
Starter motor does not rotate
STARTER MOTOR
STR-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
STR
N
P
O
REMOVAL AND INSTALLATION
STARTER MOTOR
Exploded View
INFOID:0000000011279743
Removal and Installation
INFOID:0000000011279744
REMOVAL
1. Remove battery tray. Refer to
PG-79, "Removal and Installation (Battery Tray)"
2. Remove terminal B nut and terminal B harness.
3. Remove terminal S nut and terminal S harness.
4. Remove starter motor mounting bolts.
5. Remove starter motor upward from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
• Perform the "Throttle Valve Closed Position Learning". Refer to
.
• Perform the "Accelerator Pedal Released Position Learning". Refer to
1.
Transaxle assembly
2.
"B" terminal harness
3.
"S" connector
4.
Starter motor
AWBIA1296GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст