Nissan Rogue. Manual — part 1245
WT-56
< SYMPTOM DIAGNOSIS >
LOW TIRE PRESSURE WARNING LAMP BLINKS
LOW TIRE PRESSURE WARNING LAMP BLINKS
Description
INFOID:0000000011378270
When the ignition switch is turned ON, the low tire pressure warning lamp blinks. And then 1 minute later, low
tire pressure warning lamp turns ON.
Diagnosis Procedure
INFOID:0000000011378271
1.
CHECK TIRE PRESSURE SENSOR INSTALLATION
Check visually that tire pressure sensors are installed to each wheel correctly.
NOTE:
In the following case, tire pressure monitoring system (TPMS) does not function.
• Tire pressure sensor(s) are not installed.
• Tire pressure sensor(s) of other cars are installed.
Are the genuine NISSAN tire pressure sensors installed correctly?
YES
>> GO TO 2.
NO
>> Replace and/or Install tire pressure sensor(s). Refer to
WT-68, "Removal and Installation"
. GO TO
3.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform “Self Diagnostic Result” for “AIR PRESSURE MONITOR”.
Is DTC detected?
YES
>> Perform DTC diagnosis procedure. Refer to
NO
>> GO TO 4.
3.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
Is tire pressure sensor ID registration completed?
YES
>> Adjust the tire pressure for all wheels specified to the value. Refer to
NO
>> Perform diagnosis procedure of “ID REGISTRATION CANNOT BE COMPLETED”. Refer to
4.
CHECK BCM POWER SUPPLY AND GROUND CIRCUIT
Perform the diagnosis for BCM power supply and ground circuit. Refer to
(with Intelligent Key system) or
WT-50, "WITHOUT INTELLIGENT KEY
(without Intelligent Key system).
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-75, "Removal and Installation"
(with Intelligent Key system) or
135, "Removal and Installation"
(without Intelligent Key system).
NO
>> Repair or replace malfunctioning components.
LOW TIRE PRESSURE LOCATION INDICATOR DOES NOT DISPLAY
WT-57
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
LOW TIRE PRESSURE LOCATION INDICATOR DOES NOT DISPLAY
Description
INFOID:0000000011378275
When low tire pressure, low tire location indicator does not display though low tire pressure warning lamp
turns ON.
Diagnosis Procedure
INFOID:0000000011378276
1.
CHECK COMBINATION METER
Check combination meter. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning components.
2.
CHECK LOW TIRE PRESSURE WHEEL LOCATION INDICATOR OPERATION
Check that the low tire pressure location indicator is turned OFF after turns ON for approximately 1 second,
when the ignition switch is turned ON.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> Replace the BCM. Refer to
BCS-75, "Removal and Installation"
(with Intelligent Key system) or
BCS-135, "Removal and Installation"
(without Intelligent Key system).
WT-58
< SYMPTOM DIAGNOSIS >
LOW TIRE PRESSURE LOCATION INDICATOR CONTINUES DISPLAYING
LOW TIRE PRESSURE LOCATION INDICATOR CONTINUES DISPLAYING
Description
INFOID:0000000011378277
The low tire pressure location indicator continues displaying though low tire pressure warning lamp turns/stays
OFF.
Diagnosis Procedure
INFOID:0000000011378278
1.
CHECK TIRE PRESSURE
1. Turn the ignition switch ON.
CAUTION:
Never start the engine.
2. Check the tire pressure for all wheels and adjust to the specified value. Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Inspect or repair the tires or wheels.
2.
CHECK LOW TIRE PRESSURE LOCATION INDICATOR
Check low tire pressure location indicator.
Does low tire pressure location indicator continue displaying?
YES
>> GO TO 3.
NO
>> Inspection End.
3.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform “Self Diagnostic Result” for “Air Pressure Monitor”.
Is DTC detected?
YES
>> Perform DTC diagnosis procedure. Refer to
NO
>> GO TO 4.
4.
CHECK BCM POWER SUPPLY AND GROUND CIRCUIT
Perform the trouble diagnosis for power supply and ground circuit. Refer to
(with Intelligent Key system) or
WT-50, "WITHOUT INTELLIGENT KEY
(without Intelligent Key system).
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-75, "Removal and Installation"
(with Intelligent Key system) or
135, "Removal and Installation"
(without Intelligent Key system).
NO
>> Repair or replace malfunctioning components.
ID REGISTRATION CANNOT BE COMPLETED
WT-59
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
ID REGISTRATION CANNOT BE COMPLETED
Description
INFOID:0000000011280538
The ID of the tire pressure sensor installed in each wheel cannot be registered in the tire pressure monitoring
system. Inspect the tire pressure sensor or the tire pressure monitoring system circuit.
Diagnosis Procedure
INFOID:0000000011280539
1.
CHECK TIRE PRESSURE SENSOR ACTIVATION TOOL
Check tire pressure sensor activation tool.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the battery of tire pressure sensor activation tool or repair/replace the tire pressure sen-
sor activation tool.
2.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
CAUTION:
To perform ID registration, observe the following points:
• Never register ID in a place where radio waves are interfered (e.g. radio tower).
• Never register ID in a place close to vehicles including TPMS.
Is tire pressure sensor ID registration completed?
YES
>> Inspection End.
NO
>> GO TO 3.
3.
CHECK TIRE PRESSURE SIGNAL
Change the work location and perform ID registration again.
NOTE:
Depending on the tire pressure sensor position*, a blind spot exists, and the tire pressure receiver gets poor
reception. If an ID registration is performed under this condition, the registration may not be completed. In
such case, follow the instructions below to improve the radio wave receiving environment.
• Rotate tire by 90
°, 180°, or 270°. (This Step is to change tire pressure sensor position.)
• Open the door close to the tire of which ID registration is ongoing.
*: Radio wave reception condition depends on vehicle architecture (e.g. body harness layout, tire wheel
design) or environment.
When ID registration is performed, which wheels do not react?
All wheels react and ID registration is possible.>>Inspection End.
Only certain wheel(s) do not react.>>Replace applicable tire pressure sensor. Refer to
All wheels do not react.>>Replace BCM. Refer to
BCS-75, "Removal and Installation"
system) or
BCS-135, "Removal and Installation"
(without Intelligent Key system).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст