Nissan Rogue. Manual — part 534
EC-404
< DTC/CIRCUIT DIAGNOSIS >
[QR25DE]
P1226 TP SENSOR
P1226 TP SENSOR
DTC Description
INFOID:0000000011278118
DTC DETECTION LOGIC
POSSIBLE CAUSE
Electric throttle control actuator (TP sensor 1 and 2)
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10 V at idle.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Turn ignition switch OFF, wait at least 10 seconds.
3. Turn ignition switch ON.
4. Repeat steps 2 and 3 for 32 times.
5. Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278119
1.
CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY
1. Turn ignition switch OFF.
2. Remove the intake air duct. Refer to
.
3. Check if foreign matter is caught between the throttle valve and
the housing.
Is the inspection result normal?
YES
>> Replace electric throttle control actuator. Refer to
29, "Removal and Installation"
.
NO
>> Remove the foreign matter and clean the electric throttle
control actuator inside, then perform throttle valve
closed position learning. Refer to
.
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P1226
CTP LEARNING-B1
(CTP LEARNING-B1)
Closed throttle position learning is not performed successfully, repeatedly.
JSBIA2864ZZ
P155D GENERATOR
EC-405
< DTC/CIRCUIT DIAGNOSIS >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P155D GENERATOR
DTC Description
INFOID:0000000011278120
DTC DETECTION LOGIC
POSSIBLE CAUSE
Generator
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted. always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine and let it idle at least 10 seconds.
2. Check DTC.
Is DTC detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278121
1.
CHECK CHARGING SYSTEM
Perform trouble diagnosis for charging system. Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.
CHECK INTERMITTENT INCIDENT
Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace generator. Refer to
CHG-20, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P155D
GENERATOR
(Generator)
• ECM receives mechanical malfunction signal sent from generator.
• ECM receives electrical malfunction signal sent from generator.
EC-406
< DTC/CIRCUIT DIAGNOSIS >
[QR25DE]
P1564 ASCD STEERING SWITCH
P1564 ASCD STEERING SWITCH
DTC Description
INFOID:0000000011278122
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connectors (ASCD steering switch circuit is open or shorted.)
• ASCD steering switch
• ECM
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.
CHECK DTC PRIORITY
If DTC P1564 is displayed with DTC P0603, P0604, P0605, P606, P0607, P060A, or P060B, first perform the
trouble diagnosis for DTC P0603, P0604, P0605, P606, P0607, P060A, or P060B.
Is applicable DTC detected?
YES
>> Perform diagnosis of applicable. Refer to
.
NO
>> GO TO 2.
2.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Wait at least 10 seconds.
3. Press MAIN switch for at least 10 seconds, then release it and wait at least 10 seconds.
4. Press CANCEL switch for at least 10 seconds, then release it and wait at least 10 seconds.
5. Press ACCEL/RES switch for at least 10 seconds, then release it and wait at least 10 seconds.
6. Press COAST/SET switch for at least 10 seconds, then release it and wait at least 10 seconds.
7. Check DTC.
Is DTC detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000011278123
1.
CHECK DTC PRIORITY
If DTC P1564 is displayed with DTC P0603, P0604, P0605, P606, P0607, P060A, or P060B, first perform the
trouble diagnosis for DTC P0603, P0604, P0605, P606, P0607, P060A, or P060B.
Is applicable DTC detected?
YES
>> Perform diagnosis of applicable. Refer to
.
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P1564
ASCD SW
(ASCD switch)
• An excessively high voltage signal from the ASCD steering switch is sent
to ECM.
• ECM detects that input signal from the ASCD steering switch is out of the
specified range.
• ECM detects that the ASCD steering switch is stuck ON.
P1564 ASCD STEERING SWITCH
EC-407
< DTC/CIRCUIT DIAGNOSIS >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
NO
>> GO TO 2.
2.
CHECK ASCD STEERING SWITCH CIRCUIT
With CONSULT
1. Turn ignition switch ON.
2. Select “CANCEL SW”, “RESUME/ACC SW” and “SET SW” in “DATA MONITOR” mode of “ENGINE”
using CONSULT.
3. Check each item indication as per the following conditions.
Without CONSULT
1. Turn ignition switch ON.
2. Check the voltage between ECM harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 3.
3.
CHECK ASCD STEERING SWITCH GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Disconnect combination switch (spiral cable) harness connector.
4. Check the continuity between combination switch (spiral cable) and ECM harness connector.
5. Also check harness for short to ground and to power.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.
CHECK ASCD STEERING SWITCH INPUT SIGNAL CIRCUIT
Monitor item
Condition
Indication
MAIN SW
MAIN switch
Pressed
ON
Released
OFF
CANCEL SW
CANCEL switch
Pressed
ON
Released
OFF
RESUME/ACC
SW
ACCEL/RES switch
Pressed
ON
Released
OFF
SET SW
COAST/SET switch
Pressed
ON
Released
OFF
ECM
Condition
Voltage
(Approx.)
Connector
+
-
Terminal
E16
110
111
MAIN switch: Pressed
0 V
CANCEL switch: Pressed
1 V
COAST/SET switch: Pressed
2 V
ACCEL/RES switch: Pressed
3 V
All ASCD steering switches: Released
4 V
+
−
Continuity
Combination switch
(Spiral cable)
ECM
Connector
Terminal
Connector
Terminal
M30
7
E16
111
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст