Nissan Rogue. Manual — part 883
LAN
PWBD BRANCH LINE CIRCUIT
LAN-231
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 7)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
PWBD BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000011506816
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the terminals and connectors of the automatic back door control module for damage, bend and
loose connection (unit side and connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect the connector of automatic back door control module.
2. Check the resistance between the automatic back door control module harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the automatic back door control module branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the automatic back door control module. Refer to
"AUTOMATIC BACK DOOR CONTROL UNIT : Diagnosis Procedure"
Is the inspection result normal?
YES (Present error)>>Replace the automatic back door control module. Refer to
YES (Past error)>>Error was detected in the automatic back door control module branch line.
NG
>> Repair the power supply and the ground circuit.
Automatic back door control module harness connector
Resistance (
Ω)
Connector No.
Terminal No.
B55
24
12
Approx. 54 – 66
LAN-232
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 7)]
BCM BRANCH LINE CIRCUIT
BCM BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000011506817
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the terminals and connectors of the BCM for damage, bend and loose connection (unit side and
connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect the connector of BCM.
2. Check the resistance between the BCM harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the BCM branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the BCM. Refer to the following.
• With intelligent key system:
.
• Without intelligent key system:
BCS-128, "Diagnosis Procedure"
Is the inspection result normal?
YES (Present error)>>Replace the BCM. Refer to the following.
• With intelligent key system:
BCS-75, "Removal and Installation"
.
• Without intelligent key system:
BCS-135, "Removal and Installation"
YES (Past error)>>Error was detected in the BCM branch line.
NO
>> Repair the power supply and the ground circuit.
BCM harness connector
Resistance (
Ω)
Connector No.
Terminal No.
B16
60
80
Approx. 108 – 132
LAN
AV BRANCH LINE CIRCUIT
LAN-233
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 7)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
AV BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000011506818
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the following terminals and connectors for damage, bend and loose connection (unit side and con-
nector side).
-
AV control unit
-
BCM
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1. Disconnect the connector of BCM.
2. Check the continuity between the BCM harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Check the harness and repair the root cause (CAN communication circuit 2 side). Refer to
.
3.
CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect the connector of AV control unit.
2. Check the resistance between the AV control unit harness connector terminals.
-
Models with BOSE audio system
-
Models without BOSE audio system
Is the measurement value within the specification?
YES
>> GO TO 4.
NO
>> Repair the AV control unit branch line.
4.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the AV control unit. Refer to the following.
• Navigation with BOSE:
AV-330, "AV CONTROL UNIT : Diagnosis Procedure"
• Navigation without BOSE:
AV-172, "AV CONTROL UNIT : Diagnosis Procedure"
Is the inspection result normal?
YES (Present error)>>Replace the AV control unit. Refer to following.
• Navigation with BOSE:
AV-369, "Removal and Installation"
• Navigation without BOSE:
AV-200, "Removal and Installation"
YES (Past error)>>Error was detected in the AV control unit branch line.
NO
>> Repair the power supply and the ground circuit.
BCM harness connector
Continuity
Connector No.
Terminal No.
M18
6
8
Existed
5
9
Existed
AV control unit harness connector
Resistance (
Ω)
Connector No.
Terminal No.
M108
8
17
Approx. 54 – 66
AV control unit harness connector
Resistance (
Ω)
Connector No.
Terminal No.
M101
8
17
Approx. 54 – 66
LAN-234
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 7)]
AVM BRANCH LINE CIRCUIT
AVM BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000011506819
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the following terminals and connectors for damage, bend and loose connection (unit side and con-
nector side).
-
Around view monitor control unit
-
BCM
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1. Disconnect the connector of BCM.
2. Check the continuity between the BCM harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Check the harness and repair the root cause (CAN communication circuit 2 side). Refer to
.
3.
CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect the connector of around view monitor control unit.
2. Check the resistance between the around view monitor control unit harness connector terminals.
-
With lane departure prevention system
-
Without lane departure prevention system
Is the measurement value within the specification?
YES
>> GO TO 4.
NO
>> Repair the around view monitor control unit branch line.
4.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the around view monitor control unit. Refer to the following.
AV-331, "AROUND VIEW MONITOR CONTROL UNIT : Diagnosis Procedure"
• Navigation without BOSE:
AV-172, "AROUND VIEW MONITOR CONTROL UNIT : Diagnosis Procedure"
Is the inspection result normal?
YES (Present error)>>Replace the around view monitor control unit. Refer to the following.
AV-380, "Removal and Installation"
• Navigation without BOSE:
AV-208, "Removal and Installation"
YES (Past error)>>Error was detected in the around view monitor control unit branch line.
NO
>> Repair the power supply and the ground circuit.
BCM harness connector
Continuity
Connector No.
Terminal No.
M18
6
8
Existed
5
9
Existed
Around view monitor control unit harness connector
Resistance (
Ω)
Connector No.
Terminal No.
M113
27
28
Approx. 54 – 66
Around view monitor control unit harness connector
Resistance (
Ω)
Connector No.
Terminal No.
M103
12
10
Approx. 54 – 66
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст