Nissan Rogue. Manual — part 561
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING
EM-9
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
A: Closely related B: Related C: Sometimes related —: Not related
Front of
engine
Squeak-
ing or fizz-
ing
A
B
—
B
—
B
Drive belts
(Sticking
or slip-
ping)
Drive belts deflection
Creaking
A
B
A
B
A
B
Drive belts
(Slipping)
Idler pulley bearing op-
eration
Squall
Creak
A
B
—
B
A
B
Water
pump
noise
Water pump operation
Rattle
—
—
A
—
—
—
VTC
VTC sprockets
Location
of noise
Type of
noise
Operating condition of engine
Source of
noise
Check item
Refer-
ence page
Before
warm-
up
After
warm-
up
When
start-
ing
When
idling
When
racing
While
driving
EM-10
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000011340782
The actual shape of the tools may differ from those illustrated here.
Tool number
(TechMate No.)
Tool name
Description
(J-43897-18)
Oxygen sensor thread cleaner
Reconditioning the exhaust system threads
before installing a new oxygen sensor (Use
with anti-seize lubricant shown below.)
J-43897-18 (18 mm dia.) for zirconia oxy-
gen sensor
—
(J-48891)
Spark plug socket
Removing and installing spark plug
KV10111100
(J-37228)
Seal cutter
Removing oil pan and timing chain case
KV991J0050
(J-44626)
Air fuel sensor Socket
Loosening or tightening air fuel ratio A/F sen-
sor
a: 22 mm (0.87 in)
—
(J-37067)
Seal installer
Installing rear main seal
KV10112100
(BT-8653-A)
Torque angle meter
Tightening bolts for bearing cap, cylinder
head, etc.
AWBIA2076ZZ
AWBIA1785ZZ
S-NT046
LBIA0444E
AWBIA2081ZZ
S-NT014
PREPARATION
EM-11
< PREPARATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Commercial Service Tool
INFOID:0000000011340783
Tool number
(TechMate No.)
Tool name
Description
KV10117100
(J-36471-A)
Heated oxygen sensor wrench
Loosening or tightening heated oxygen sen-
sor
For 22 mm (0.87 in) hexagon nut
KV10116200
(J-26336-A)
Valve spring compressor
1. KV10115900
(J-26336-20)
Attachment
2. KV10109220
( — )
Adapter
Disassembling valve mechanism
Part (1) is a component of KV10116200 (J-
26336-A), but part (2) is not.
Manual lift table caddy
Removing and installing engine
ST16610001
(J-23907)
Pilot converter puller
Removing crankshaft pilot converter
Tube presser
Pressing the tube of liquid gasket
Piston ring compressor
Installing piston assembly into cylinder bore
NT379
PBIC1650E
ZZA1210D
S-NT045
S-NT052
S-NT044
EM-12
< PREPARATION >
PREPARATION
Pulley holder
Crankshaft pulley removing and installing
Pulley puller
Removing crankshaft pulley
Valve seat cutter set
Finishing valve seat dimensions
Piston ring expander
Removing and installing piston ring
—
(J-39386)
Valve oil seal drift
Installing valve oil seal
Valve guide drift
Removing and installing valve guide
Intake & Exhaust:
a: 9.5 mm (0.374 in) dia.
b: 5.5 mm (0.217 in) dia.
Valve guide reamer
1: Reaming valve guide inner hole
2: Reaming hole for oversize valve guide
Intake & Exhaust:
d
1
: 6.0 mm (0.236 in) dia.
d
2
: 10.2 mm (0.402 in) dia.
Tool number
(TechMate No.)
Tool name
Description
ZZA1010D
NT676
S-NT048
S-NT030
NT024
S-NT015
S-NT016
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст