Nissan Rogue. Manual — part 371
DLK-326
< BASIC INSPECTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
INSPECTION AND ADJUSTMENT
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000011279086
Perform the system initialization when replacing BCM, replacing keyfob or registering an additional keyfob.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement
INFOID:0000000011279087
Refer to the CONSULT Immobilizer mode and follow the on-screen instructions.
2015 Rogue NAM
U1000 CAN COMM CIRCUIT
DLK-327
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DTC/CIRCUIT DIAGNOSIS
U1000 CAN COMM CIRCUIT
Description
INFOID:0000000011378205
.
DTC Logic
INFOID:0000000011378206
DTC DETECTION LOGIC
NOTE:
U1000 can be set if a module harness was disconnected and reconnected, perhaps during a repair. Confirm
that there are actual CAN diagnostic symptoms and a present DTC by performing the Self Diagnostic Result
procedure.
Diagnosis Procedure
INFOID:0000000011378207
1.
PERFORM SELF DIAGNOSTIC
1. Turn ignition switch ON and wait for 2 second or more.
2. Check “Self Diagnostic Result”.
Is “CAN COMM CIRCUIT” displayed?
YES
>> Perform CAN Diagnosis as described in DIAGNOSIS section of CONSULT Operation Manual.
NO
>> Refer to
GI-44, "Intermittent Incident"
.
CONSULT Display
DTC Detection Condition
Possible cause
CAN COMM CIRCUIT
[U1000]
When any listed module cannot communicate with CAN
communication signal continuously for 2 seconds or
more with ignition switch ON.
In CAN communication system, any item (or items)
of the following listed below is malfunctioning:
• Transmission
• Receiving (ECM)
• Receiving (VDC/TCS/ABS)
• Receiving (METER/M&A)
• Receiving (TCM)
• Receiving (IPDM E/R)
2015 Rogue NAM
DLK-328
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
U1010 CONTROL UNIT (CAN)
U1010 CONTROL UNIT (CAN)
DTC Logic
INFOID:0000000011378208
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000011378209
1.
REPLACE BCM
When DTC U1010 is detected, replace BCM.
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
CONSULT Display
DTC Detection Condition
Possible Cause
CAN COMM CIRCUIT
[U1010]
BCM detected internal CAN communication circuit mal-
function.
BCM
2015 Rogue NAM
POWER SUPPLY AND GROUND CIRCUIT
DLK-329
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
POWER SUPPLY AND GROUND CIRCUIT
BCM
BCM : Diagnosis Procedure
INFOID:0000000011378210
Regarding Wiring Diagram information, refer to
1.
CHECK FUSE
Check that the following fuse is not blown.
Is the fuse blown?
YES
>> Replace the blown fuse after repairing the affected circuit.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1. Disconnect BCM connector M20.
2. Check voltage between BCM connector M20 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connectors.
3.
CHECK GROUND CIRCUIT
Check continuity between BCM connector M20 and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair or replace harness or connectors.
Terminal No.
Signal name
Fuse No.
161
BCM power supply
7 (10A)
BCM
Ground
Voltage
(Approx.)
Connector
Terminal
M20
161
—
Battery voltage
BCM
Ground
Continuity
Connector
Terminal
M20
170
—
Yes
171
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст