Nissan Rogue. Manual — part 1047
SE-54
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
PASSENGER POWER SEAT
25. Side air bag module (not service-
able)
26. Seatback bracket
27. Seatback frame
28. Headrest holder (locked)
29. Headrest holder (free)
AWJIA1616ZZ
1.
Headrest
2.
Seatback board
3.
Seatback support
4.
Seatback heater
5.
Seat cushion trim
6.
Seat cushion pad
7.
Seat cushion trim
8.
Seat cushion pad
9.
Seat cushion heater
10. Seat cushion support
11. Seat cushion silencer
12. Seat harness
13. Occupant classification system
harness
14. Seat cushion outer finisher
(LH)
15. Seat cushion inner finisher (LH)
FRONT SEAT
SE-55
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
PASSENGER MANUAL SEAT
16. Occupant classification system
sensor
17. Occupant classification sys-
tem control unit
18. Occupant classification system
bracket
19. Wiring harness bracket
20. Power seat switch
21. Seat cushion outer finisher (RH)
22. Seat slide knob
23. Seat recline knob
24. Seat cushion inner finisher (RH)
25. Seat cushion rear finisher (RH)
26. Side air bag module (not ser-
viceable)
27. Seat cushion frame
28. Seat belt buckle
29. Seat cushion rear finisher (LH) 30. Seatback frame
31. Seatback bracket
32. Headrest holder (locked)
33. Headrest holder (free
AWJIA1617ZZ
SE-56
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
Seatback
INFOID:0000000011280467
DISASSEMBLY
WARNING:
Do not leave any objects (screwdrivers, tools, etc.) on the seat during seatback repair. It can lead to
personal injury if the side air bag module should accidentally deploy.
CAUTION:
• Before servicing, turn the ignition switch OFF, disconnect both battery terminals then wait at least
three minutes.
• Always work from the side or back of the seatback, do not work in front of seat.
• Do not use air tools or electric tools for servicing the seat assembly.
• Do not insert any objects into the side air bag module.
• Do not attempt to disassemble the side air bag module.
• Do not expose the side air bag module to temperatures exceeding 93
°C (199°F).
• Do not expose the side air bag module to any oil, grease, detergent or water.
• During disassembly, do not damage the seatback board, connectors, retainers, clips, module har-
ness or the side air bag module.
NOTE:
• If the vehicle has been involved in a collision and the side air bag module has deployed, the seat trim must
be replaced.
• Front seat (LH) shown, front seat (RH) similar.
1. Remove driver side front seat or front seat passenger side. Refer to
SE-32, "DRIVER SIDE : Removal and
SE-35, "PASSENGER SIDE : Removal and Installation"
(PASSENGER
SIDE).
2. Release J-hooks (1) fastener (LH/RH).
3. Press the headrest holder lock button, then lift headrest up and remove.
1.
Headrest
2.
Seatback board
3.
Seatback support
4.
Seatback heater (if equipped)
5.
Seatback trim
6.
Seatback pad
7.
Seat cushion trim
8.
Seat cushion pad
9.
Seat cushion heater (if
equipped)
10. Seat cushion support
11. Seat cushion silencer
12. Seat harness
13. Occupant classification system
harness
14. Seat cushion outer finisher
(LH)
15. Seat cushion inner finisher (LH)
16. Occupant classification system
sensor
17. Occupant classification sys-
tem control unit
18. Occupant classification system
control unit bracket
19. Wiring harness bracket
20. Seat cushion outer finisher
21. Recline lever
22. Seat cushion inner finisher (RH) 23. Seat cushion rear finisher
(RH)
24. Side air bag module (not service-
able)
25. Seat cushion frame
26. Seat belt buckle
27. Seat cushion rear finisher (LH)
28. Seatback frame
29. Seatback bracket
30. Headrest holder (free)
31. Headrest holder (locking)
ALJIA1426ZZ
FRONT SEAT
SE-57
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
4. Release headrest holder locks as shown and remove headrest
holders.
CAUTION:
Before removing/installing the headrest holder, check its
orientation (front/rear and right/left).
5. Release side air bag module harness clips from seat frame.
NOTE:
Take note of harness routing and attachment location for correct installation.
6. Remove side air bag module harness nuts (A).
CAUTION:
Do not reuse side air bag module nuts.
7. Remove seat cushion outer finisher (LH).
a. For manual seat:
i.
Remove snap ring (1) as shown (
) using a suitable tool, then
remove the recline lever (2).
ii.
Release pawl and remove lift lever.
JMJIA4073ZZ
ALJIA1428ZZ
AWJIA1562ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст