Nissan Rogue. Manual — part 1139
ST-6
< BASIC INSPECTION >
STEERING WHEEL
BASIC INSPECTION
STEERING WHEEL
Inspection
INFOID:0000000011280292
STEERING WHEEL AXIAL END PLAY
1. Check installation conditions of steering gear, front suspension, axle and steering column.
2. Check if movement exists when steering wheel is moved up and down, to the left and right and to the axial
direction.
3. Check the following items when steering wheel axial end play is out of the standard.
• Check the steering column condition. Refer to
.
• Check steering gear condition for looseness. Refer to
STEERING WHEEL PLAY
1. Turn steering wheel so that front wheels come to the straight-ahead position.
2. Start engine and lightly turn steering wheel to the left and right until front wheels start to move.
3. Measure steering wheel movement on the outer circumference.
4. Check the following items when steering wheel play is out of the standard.
• Check backlash for each joint of steering column.
• Check installation condition of steering gear.
NEUTRAL POSITION STEERING WHEEL
1. Make sure that steering gear, steering column and steering wheel are installed in the correct position.
2. Perform neutral position inspection after wheel alignment. Refer to
3. Set vehicle to the straight-ahead position and confirm steering wheel is in the neutral position.
4. Loosen outer socket lock nut and turn inner socket to left and right equally to make fine adjustments if
steering wheel is not in the neutral position.
STEERING WHEEL TURNING FORCE
1. Park vehicle on a level and dry surface, set parking brake.
2. Tires need to be inflated normal pressure. Refer to
3. Start engine.
4. Check steering wheel turning force, using Tool, when steering
wheel has been turned 360
° from neutral position.
FRONT WHEEL TURNING ANGLE
1. Check front wheel turning angle after toe-in inspection. Refer to
Steering wheel axial end play
: Refer to
Steering wheel play
: Refer to
Tool number
: — (J-44372)
Steering wheel turning
force
: Refer to
.
JSGIA0027ZZ
STEERING WHEEL
ST-7
< BASIC INSPECTION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
2. Place front wheels on turning radius gauges and rear wheels on
stands, so that vehicle can be level.
3. Check the maximum inner and outer wheel turning angles for LH
and RH road wheels.
4. With the engine at idle, turn steering wheel from full left stop to
full right stop and measure the turning angles.
5. Check the following items when turning angle is outside of the
standard.
a. Check the neutral position of the rack stroke (L).
b. Check steering gear, steering column and front suspension
components for wear or damage if any of the turning angles are
different from the specified value. Replace components if any
conditions are outside of the standard.
NOTE:
Steering angles are not adjustable.
FAA0016D
Inner wheel (Angle: A)
: Refer to
.
Outer wheel (Angle: B)
: Refer to
.
SGIA0055E
Rack stroke in neutral
position (L)
: Refer to
.
SGIA0629J
ST-8
< BASIC INSPECTION >
STEERING COLUMN
STEERING COLUMN
Inspection
INFOID:0000000011280293
HOLE COVER SEAL, HOLE COVER AND LOWER SHAFT
Check each part of hole cover seal, hole cover and steering column and lower shaft for damage or other mal-
functions. Replace if necessary.
STEERING COLUMN
• Check each part of steering column for damage or other malfunctions. Replace entire steering column if any
parts are damaged.
• Measure the steering column length (with the steering wheel and airbag module installed) if vehicle has
been involved in a minor collision. Replace steering column if outside the specifications.
• Measure steering column rotating torque using suitable tool. Replace steering column if outside the stan-
dard.
• Check tilt and telescopic mechanism operating range (L
1
), (L
2
) as
shown.
Steering column length (with steering
wheel and air bag module installed)
: Refer to
.
Rotating torque
: Refer to
Tilt operating range (L
1
)
: Refer to
.
Telescopic operating range
(L
2
)
: Refer to
.
ALGIA0106ZZ
STEERING GEAR AND LINKAGE
ST-9
< BASIC INSPECTION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
STEERING GEAR AND LINKAGE
Inspection
INFOID:0000000011280294
STEERING GEAR
• Check boot for cracks, and replace it if an abnormal condition is detected.
• Check gear housing for damage and scratches (inner wall). Replace if there are any abnormal conditions.
OUTER SOCKET AND INNER SOCKET
• Ball joint swinging torque
- Hook Tool at the measuring point and pull Tool. Make sure that
Tool reads the specified value when ball stud and inner socket start
to move. Replace outer socket or steering gear (inner socket) if
they are outside the standard.
• Ball joint rotating torque
- Make sure that the reading is within the following specified range
using suitable tool (A). Replace outer socket if the reading is out-
side the specification.
• Ball joint axial end play
- Apply an axial load of 490 N (50 kg, 111 lb) to ball stud. Measuring
the amount of stud movement using a dial gauge, make sure that
the value is within specification. Replace outer socket (A) and
inner socket (B) if the measured value is outside specification.
RACK SLIDING FORCE
1. Set the front wheels and tires to the straight-ahead position.
2. Remove the column hole cover. Refer to
3. Remove the lower cover seal. Refer to
4. Remove the joint retaining bolt and separate the steering column joint from the steering gear pinion shaft.
.
CAUTION:
With the steering linkage disconnected, the spiral cable may snap by turning the steering wheel
beyond the limited number of turns. Secure the steering wheel.
Measuring point of outer socket (1)
: Ball stud upper side (A)
Measuring point of inner socket (2)
: Point (B)
Tool number
: — (J-44372)
Swinging torque : Refer to
JPGIA0188ZZ
Rotating torque
: Refer to
AWGIA0228ZZ
Axial end play
: Refer to
.
JSGIA0109ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст