Nissan Rogue. Manual — part 385
DLK-382
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
HOOD LOCK
4. Install so that static closing force of hood is 315-490 N (32.1-50.0 kg–m, 70.8-110.2 ft–lb).
NOTE:
• Do not exert vertical force on right side and left side of hood lock.
• Do not press simultaneously on both sides.
5. Check the hood lock lubrication condition. If necessary, apply a suitable multi-purpose grease to hood lock
assembly.
SECONDARY LATCH
SECONDARY LATCH : Removal and Installation
INFOID:0000000011279167
REMOVAL
1. Remove front grille. Refer to
EXT-23, "Removal and Installation"
2. Disconnect secondary latch cable from hood lock assembly.
3. Remove bolts and secondary latch.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Tighten bolts to specified torque. Refer to
• Check that secondary latch cable is properly engaged with hood lock.
HOOD LOCK RELEASE CABLE
HOOD LOCK RELEASE CABLE : Removal and Installation
INFOID:0000000011279168
REMOVAL
1. Remove fender protector (LH). Refer to
EXT-28, "FENDER PROTECTOR : Removal and Installation"
2. Remove front grille. Refer to
EXT-23, "Removal and Installation"
3. Disconnect hood lock release cable from hood lock release handle and hood lock.
4. Release hood lock release cable clips using a suitable tool.
5. Remove grommet on the lower dash and carefully pull the hood lock release cable into the passenger
compartment.
CAUTION:
While pulling, be careful not to damage (peel) the outside of hood lock release cable.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Be careful not to bend cable too much, keep the radius 100 mm (3.94 in) or more.
• Check that cable is not offset from the positioning grommet,
and apply the sealant to the grommet (at * mark) properly.
• Check that hood lock release cable is properly engaged with hood lock assembly.
• After installation, perform hood assembly adjustment procedure. Refer to
• After adjusting, perform hood lock inspection. Refer to
DLK-381, "HOOD LOCK : Inspection"
HOOD LOCK RELEASE HANDLE
PIIB5801E
2015 Rogue NAM
HOOD LOCK
DLK-383
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HOOD LOCK RELEASE HANDLE : Removal and Installation
INFOID:0000000011279169
REMOVAL
1. Remove fuel filler lid/hood lock release handle bolts (A).
2. Disconnect fuel filler lid release cable (2) from fuel filler lid
release handle (1).
3. Disconnect hood lock release cable (4) from hood lock release
handle (3).
4. Remove hood lock release handle.
INSTALLATION
Installation is in the reverse order of removal.
ALKIA3422ZZ
2015 Rogue NAM
DLK-384
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
FRONT DOOR LOCK
Exploded View
INFOID:0000000011279170
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000011279171
REMOVAL
1. Remove front door finisher. Refer to
INT-15, "Removal and Installation"
2. Remove vapor barrier.
3. Remove front door lock bolts (A).
1.
Front door lock
2.
Inside handle
3.
Door key cylinder rod (LH only)
4.
Outside handle bracket
5.
Front gasket
6.
Outside handle
7.
Outside handle escutcheon / door key
cylinder (LH only)
8.
Rear gasket
A.
Clip
AWKIA2920ZZ
ALKIA3355ZZ
2015 Rogue NAM
FRONT DOOR LOCK
DLK-385
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
4. Disconnect door key cylinder rod (LH only) (1) from front door
lock (2) (LH only).
5. Disconnect door lock cables from inside handle and outside handle..
6. Disconnect the harness connector from the front door lock and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse front door lock bolts.
• Tighten bolts to specification. Refer to
• After installation, check door lock cables are properly engaged to inside handle and outside handle
bracket.
• When installing door key cylinder rod (LH only), be sure to rotate door key cylinder rod holder until a
click is felt.
• After installation, check door open/close and lock/unlock operation.
• Check door lock assembly for poor lubrication. If necessary apply a suitable multi-purpose grease.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000011279172
REMOVAL
1. Remove front door finisher. Refer to
INT-15, "Removal and Installation"
2. Remove inside handle bolt (B).
3. Disconnect the door lock cables (A) and remove inside handle
(1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check door lock cables are properly engaged to inside handle.
• After installation, check door open/close and lock/unlock operation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000011279173
REMOVAL
1. Fully close front door glass.
2. Remove front door finisher. Refer to
INT-15, "Removal and Installation"
ALKIA2487ZZ
ALKIA3392ZZ
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст