Nissan Rogue. Manual — part 1186
TM-116
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A
Is it necessary to erase permanent DTC?
YES
>> GO TO 3.
NO
>> GO TO 7.
3.
CHECK DTC (ECM AND TCM)
Check the DTC.
Is any DTC other than “P0711” detected?
YES
>> Check DTC detected item. Refer to
(TCM).
NO
>> GO TO 4.
4.
PERFORM DTC CONFIRMATION PROCEDURE (PART 1)
TESTING CONDITION:
• While performing the following procedure, do not add fuel.
• Before performing the following procedure, check that fuel level is between 1/4 and 4/4.
• Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.
With CONSULT
1. Move the vehicle to a cool place.
NOTE:
Cool the vehicle in an environment of ambient air temperature between
−10°C (14°F) and 35°C (95°F).
2. Turn ignition switch OFF and leave the vehicle for 12 hours.
CAUTION:
Never turn ignition switch ON during this procedure.
NOTE:
The vehicle must be cooled with the food open.
3. Turn ignition switch ON.
CAUTION:
Never start the engine.
4. Select “Data Monitor” in “TRANSMISSION”.
5. Select “FLUID TEMP”.
6. Record CVT fluid temperature.
7. Start engine and let it idle for 5 minutes or more.
CAUTION:
Never turn ignition switch OFF during idling.
8. Check 1st trip DTC.
With GST
1. Move the vehicle to a cool place.
NOTE:
Cool the vehicle in an environment of ambient air temperature between
−10°C (14°F) and 35°C (95°F).
2. Turn ignition switch OFF and leave the vehicle for 12 hours.
CAUTION:
Never turn ignition switch ON during this procedure.
NOTE:
The vehicle must be cooled with the food open.
3. Start engine and let it idle for 5 minutes or more.
CAUTION:
Never turn ignition switch OFF during idling.
4. Check 1st trip DTC.
Is “P0711” detected?
YES
>> Go to
NO-1 (With CONSULT)>>GO TO 5.
NO-2 (With GST)>>GO TO 6.
5.
CHECK CVT FLUID TEMPERATURE
With CONSULT
1. Select “Data Monitor” in “TRANSMISSION”.
2. Select “FLUID TEMP”.
Is the value of “FLUID TEMP” 10
°C (50°F) or more?
YES
>> INSPECTION END
NO
>> GO TO 6.
P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A
TM-117
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
6.
PERFORM DTC CONFIRMATION PROCEDURE (PART 2)
With CONSULT
1. Drive the vehicle for the total minutes specified in the Driving time column below with the following condi-
tions satisfied.
2. Stop the vehicle.
3. Check the first trip DTC.
With GST
1. Drive the vehicle and maintain the following conditions for 20 minutes or more.
2. Stop the vehicle.
3. Check the first trip DTC.
Is “P0711” detected?
YES
>> Go to
NO-1 >> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2 >> Confirmation after repair: INSPECTION END
7.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1. Turn ignition switch OFF and cool the engine.
2. Turn ignition switch ON.
CAUTION:
Never start the engine.
3. Select “Data Monitor” in “TRANSMISSION”.
4. Select “FLUID TEMP”.
5. Record CVT fluid temperature.
6. Start the engine and wait for at least 2 minutes.
7. Drive the vehicle for the total minutes specified in the Driving time column below with the following condi-
tions satisfied.
Selector lever
: “D” position
Accelerator pedal position
: 1.0/8 or more
Vehicle speed
: 10 km/h (7 MPH) or more
CVT fluid temperature before engine start
Driving time
−40°C (−40°F) – −31°C (−23.8°F)
20 minutes or more
−30°C (−22°F) – −21°C (−5.8°F)
18 minutes or more
−20°C (−4°F) – −11°C (−12.2°F)
14 minutes or more
−10°C (14°F) – −1°C (30.2°F)
10 minutes or more
0
°C (32°F) – 9°C (48.2°F)
7 minutes or more
Selector lever
: “D” position
Accelerator pedal position
: 1.0/8 or more
Vehicle speed
: 10 km/h (7 MPH) or more
Selector lever
: “D” position
Accelerator pedal position
: 1.0/8 or more
Vehicle speed
: 10 km/h (7 MPH) or more
CVT fluid temperature before engine start
Driving time
−40°C (−40°F) – −31°C (−23.8°F)
20 minutes or more
−30°C (−22°F) – −21°C (−5.8°F)
18 minutes or more
−20°C (−4°F) – −11°C (−12.2°F)
14 minutes or more
−10°C (14°F) – −1°C (30.2°F)
10 minutes or more
TM-118
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A
8. Stop the vehicle.
9. Check the first trip DTC.
With GST
1. Turn ignition switch OFF and cool the engine.
2. Start the engine and wait for at least 2 minutes.
3. Drive the vehicle and maintain the following conditions for 20 minutes or more.
4. Stop the vehicle.
CAUTION:
Never turn ignition switch OFF
5. Check the first trip DTC.
Is “P0711” detected?
YES
>> Go to
NO
>> GO TO 8.
8.
CHECK CVT FLUID TEMPERATURE SENSOR
1. Turn ignition switch OFF.
2. Disconnect CVT unit connector.
3. Check resistance between CVT unit connector terminals.
Is the inspection result normal?
YES-1 >> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
YES-2 >> Confirmation after repair: INSPECTION END
NO
>> There is a malfunction of CVT fluid temperature sensor. Replace transaxle assembly. Refer to
TM-220, "Removal and Installation"
Diagnosis Procedure
INFOID:0000000011279340
1.
CHECK CVT FLUID TEMPERATURE SENSOR
1. Turn ignition switch OFF.
2. Disconnect CVT unit connector.
3. Check resistance between CVT unit connector terminals.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 4.
0
°C (32°F) – 9°C (48.2°F)
7 minutes or more
Other than the above
— (Go to “8.CHECK CVT FLU-
ID TEMPERATURE SENSOR”)
Selector lever
: “D” position
Accelerator pedal position
: 1.0/8 or more
Vehicle speed
: 10 km/h (7 MPH) or more
CVT fluid temperature before engine start
Driving time
CVT unit
Condition
Resistance
(Approx.)
Terminal
12 – 18
CVT fluid temperature: 20
°C (68°F)
6.5 k
Ω
CVT fluid temperature: 50
°C (122°F)
2.2 k
Ω
CVT fluid temperature: 80
°C (176°F)
0.87 k
Ω
CVT unit
Condition
Resistance
(Approx.)
Connector
Terminal
F209
12 – 18
CVT fluid temperature: 20
°C (68°F)
6.5 k
Ω
CVT fluid temperature: 50
°C (122°F)
2.2 k
Ω
CVT fluid temperature: 80
°C (176°F)
0.87 k
Ω
P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A
TM-119
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2.
CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (CVT FLUID TEMPERATURE SENSOR) (PART 1)
1. Disconnect the TCM connector.
2. Check continuity between TCM harness connector terminals and CVT unit harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (CVT FLUID TEMPERATURE SENSOR) (PART 2)
Check continuity between TCM harness connector terminals and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace damaged parts.
4.
CHECK DTC (TCM)
With CONSULT
1. Perform “DTC CONFIRMATION PROCEDURE”. Refer to
2. Select “Self Diagnostic Results” in “TRANSMISSION”.
Is “P0711” detected?
YES
>> There is a malfunction of the CVT fluid temperature sensor. Replace the transaxle assembly.
TM-220, "Removal and Installation"
.
NO
>> INSPECTION END
TCM
CVT unit
Continuity
Connector
Terminal
Connector
Terminal
F75
11
F74
18
Existed
12
12
TCM
—
Continuity
Connector
Terminal
F75
11
Ground
Not existed
12
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст