Nissan Rogue. Manual — part 996
PWC-66
< REMOVAL AND INSTALLATION >
POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH
POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH
Removal and Installation
INFOID:0000000011278745
REMOVAL
1. Remove the front door pull handle bracket (RH). Refer to
.
2. Release pawls using a suitable tool (A) and remove front door
power window and door lock/unlock switch finisher (RH) (1).
: Pawl
3. Disconnect the harness connector from the front door power window and door lock/unlock switch (RH).
4. Release pawls, then separate front power window and door
lock/unlock switch (RH) (1) from switch finisher (2).
: Pawl
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
When the front power window and door lock/unlock switch (RH) is removed or replaced, it is necessary to per-
form the initialization procedure. Refer to
PWC-28, "ADDITIONAL SERVICE WHEN REMOVING BATTERY
NEGATIVE TERMINAL : Description"
.
ALKIA3472ZZ
ALKIA3473ZZ
REAR POWER WINDOW SWITCH
PWC-67
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
REAR POWER WINDOW SWITCH
Removal and Installation
INFOID:0000000011278746
REMOVAL
1. Remove screw cover (1).
2. Remove screw (A).
3. Release pawls using a suitable tool (A) and remove rear power
window switch finisher (1).
: Pawl
4. Disconnect harness connector from rear power window switch.
5. Release the pawls, then separate the rear power window switch
(1) from the switch finisher (2).
: Pawl
INSTALLATION
Installation is in the reverse order of removal.
ALJIA1377ZZ
ALJIA1378ZZ
ALJIA1344ZZ
ALKIA3475ZZ
PWO
PWO-1
ELECTRICAL & POWER CONTROL
C
D
E
F
G
H
I
J
K
L
B
SECTION
PWO
A
O
P
N
CONTENTS
POWER OUTLET
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
Component Parts Location . . . . . . . . . ....
WIRING DIAGRAM . . . . . . . . . ...
POWER SOCKET . . . . . . . . . . . ..
Wiring Diagram . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . .
POWER SOCKET . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . ..
PWO-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000011278432
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст