Nissan Rogue. Manual — part 172
C1160 DECEL G SEN SET
BRC-99
< DTC/CIRCUIT DIAGNOSIS >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
C1160 DECEL G SEN SET
DTC Logic
INFOID:0000000011280625
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF DIAGNOSTIC RESULT
With CONSULT.
1. Turn ignition switch OFF to ON.
2. Perform “Self Diagnostic Result”.
Is DTC C1160 detected?
YES
>> Proceed to diagnosis procedure. Refer to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011280626
1.
DECEL G SENSOR CALIBRATION
Perform decel G sensor calibration. Refer to
>> GO TO 2.
2.
CHECK SELF DIAGNOSTIC RESULT
With CONSULT.
Perform “Self Diagnostic Result”.
Is DTC C1160 detected?
YES
>> GO TO 3.
NO
>> Inspection End.
3.
CHECK YAW RATE/SIDE/DECEL G SENSOR SYSTEM
Check yaw rate/side/decel G sensor system. Refer to
Is the inspection result normal?
YES
>> Replace ABS actuator and electric unit (control unit). Refer to
BRC-134, "Removal and Installa-
.
NO
>> Repair or replace malfunctioning components.
DTC
Display Item
Malfunction detected condition
Possible causes
C1160
DECEL G SEN SET
When calibration of yaw rate/side/decel G sensor is
not complete.
• Yaw rate/side/decel G sensor
• Harness or connector
• ABS actuator and electric unit
(control unit)
• Decel G sensor calibration is
not performed
BRC-100
< DTC/CIRCUIT DIAGNOSIS >
[VDC/TCS/ABS]
C1164, C1165 CV SYSTEM
C1164, C1165 CV SYSTEM
DTC Logic
INFOID:0000000011280627
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF DIAGNOSTIC RESULT
With
CONSULT.
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result”.
Is DTC “C1164” or “C1165” detected?
YES
>> Proceed to diagnosis procedure. Refer to
BRC-100, "Diagnosis Procedure"
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011280628
Regarding Wiring Diagram information, refer to
1.
CONNECTOR INSPECTION
1. Turn ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) connectors.
3. Check connectors and terminals for deformation, disconnection, looseness or damage.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace as necessary.
2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) BATTERY POWER SUPPLY
Check voltage between ABS actuator and electric unit (control unit) connector E125 terminals 1, 25 and
ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning components.
3.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) GROUND CIRCUIT
Check continuity between ABS actuator and electric unit (control unit) connector E125 terminals 13, 38 and
ground.
DTC
Display Item
Malfunction detected condition
Possible causes
C1164
CV 1
When a malfunction is detected in cut valve 1.
• Harness or connector
• ABS actuator and electric unit
(control unit)
• Fusible link
• Battery power supply system
C1165
CV 2
When a malfunction is detected in cut valve 2.
ABS actuator and electric unit (control unit)
—
Voltage
(Approx.)
Connector
Terminal
E125
1
Ground
Battery voltage
25
C1164, C1165 CV SYSTEM
BRC-101
< DTC/CIRCUIT DIAGNOSIS >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
Is the inspection result normal?
YES
>> Replace ABS actuator and electric unit (control unit). Refer to
BRC-134, "Removal and Installa-
.
NO
>> Repair or replace malfunctioning components.
ABS actuator and electric unit (control unit)
—
Continuity
Connector
Terminal
E125
13
Ground
Yes
38
BRC-102
< DTC/CIRCUIT DIAGNOSIS >
[VDC/TCS/ABS]
C1170 VARIANT CODING
C1170 VARIANT CODING
DTC Logic
INFOID:0000000011280629
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF DIAGNOSTIC RESULT
With
CONSULT.
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result”.
Is DTC C1170 detected?
YES
>> Proceed to diagnosis procedure. Refer to
BRC-102, "Diagnosis Procedure"
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011280630
1.
REPLACE ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Replace ABS actuator and electric unit (control unit) even if other DTCs are displayed with “VARIANT COD-
ING” in“Self Diagnostic Result”.
>> Replace ABS actuator and electric unit (control unit). Refer to
BRC-134, "Removal and Installa-
.
DTC
Display Item
Malfunction detected condition
Possible causes
C1170
VARIANT CODING
When the information in ABS actuator and electric
unit (control unit) is not the same.
ABS actuator and electric unit
(control unit)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст