Nissan Rogue. Manual — part 417
DLN-112
< PERIODIC MAINTENANCE >
[REAR FINAL DRIVE: R145]
REAR DIFFERENTIAL GEAR OIL
PERIODIC MAINTENANCE
REAR DIFFERENTIAL GEAR OIL
Inspection
INFOID:0000000011278405
OIL LEAKS
Make sure that oil is not leaking from final drive assembly or around it.
OIL LEVEL
• Remove filler plug (1) and check oil level (A) from filler plug mount-
ing hole as shown.
CAUTION:
Do not start engine while checking oil level.
• Set a new gasket on filler plug and install it on final drive assembly.
CAUTION:
Do not reuse gasket.
Draining
INFOID:0000000011278406
1. Stop engine.
2. Remove drain plug (1) and drain gear oil.
3. Set a new gasket on drain plug and install it to final drive assem-
bly and tighten to the specified torque. Refer to
CAUTION:
Do not reuse gasket.
Refilling
INFOID:0000000011278407
1. Remove filler plug (1). Fill with new gear oil until oil level (A)
reaches the specified level near filler plug hole.
2. After refilling oil, check oil level. Set a new gasket to filler plug,
then install it to final drive assembly. Refer to
CAUTION:
Do not reuse gasket.
ALDIA0509ZZ
ALDIA0510ZZ
Oil grade and viscosity
: Refer to
.
Oil capacity
: Refer to
.
ALDIA0509ZZ
DRIVE PINION OIL SEAL
DLN-113
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
REMOVAL AND INSTALLATION
DRIVE PINION OIL SEAL
Exploded View
INFOID:0000000011278408
Removal and Installation
INFOID:0000000011278409
REMOVAL
1. Remove electric controlled coupling. Refer to
DLN-115, "Removal and Installation"
2. Using a suitable tool remove drive pinion oil seal.
CAUTION:
Do not damage rear final drive assembly.
INSTALLATION
1. Install drive pinon oil seal (1) using Tool (A).
CAUTION:
• Do not reuse oil seal.
• When installing, do not incline oil seal.
• Apply multi-purpose grease onto oil seal lips, and gear oil
onto the circumference of oil seal.
2. Install electric controlled coupling. Refer to
DLN-115, "Removal and Installation"
.
3. Install rear propeller shaft. Refer to
4. When oil leaks while removing, check oil level after the installation. Refer to
Rear final drive assembly
Drive pinion oil seal
Electric controlled coupling assembly
Oil seal lip
: Always replace after every disassembly.
: Apply gear oil.
: Apply multi-purpose grease.
JSDIA5261ZZ
Oil seal installation
length (B)
: 0.8 - 1.2 mm (0.031 - 0.047 in)
Tool number
: KV38100200 (J-26233)
: ST27861000 (
—
)
ALDIA0522ZZ
DLN-114
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R145]
SIDE OIL SEAL
SIDE OIL SEAL
Exploded View
INFOID:0000000011278410
Removal and Installation
INFOID:0000000011278411
REMOVAL
1. Remove rear drive shaft (LH/RH) with power tool. Refer to
2. Remove side oil seal (LH/RH), using a suitable tool.
CAUTION:
Do not damage gear carrier and rear cover.
INSTALLATION
1. Install side oil seals until it becomes flush with the carrier end,
using Tool (A).
CAUTION:
• Do not reuse oil seals.
• When installing, do not incline oil seals.
• Apply multi-purpose grease onto oil seal lips, and gear oil
onto the circumference of oil seal.
2. Install rear drive shafts. Refer to
3. When oil leaks while removing, check oil level after the installa-
.
Rear final drive assembly
Side oil seal
Oil seal lip
: Always replace after every disassembly.
: Apply gear oil.
: Apply multi-purpose grease.
JSDIA5269ZZ
PDIA0431E
Tool number : KV38100200 (J-26233)
JSDIA0201ZZ
ELECTRIC CONTROLLED COUPLING
DLN-115
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
ELECTRIC CONTROLLED COUPLING
Exploded View
INFOID:0000000011278412
Removal and Installation
INFOID:0000000011278413
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove rear propeller shaft from the electric controlled coupling, and support the end of the propeller
shaft. Refer to
2. Remove electric controlled coupling breather hose (2) from elec-
tric controlled coupling (1).
3. Disconnect the electric controlled coupling harness connector
(A).
4. Remove harness connector bracket.
5. Remove bolts from electric controlled coupling.
6. Remove the electric controlled coupling.
CAUTION:
Be careful that the wave spring does not fall out or get damaged when removing the electric con-
trolled coupling.
Rear final drive assembly
Wave spring
Electric controlled coupling assembly
Reamer bolt
Connector bracket
Stud bolt
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
JSDIA5440GB
ALDIA0516ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст