Nissan Rogue. Manual — part 227
DAS
ACTION TEST
DAS-79
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
ACTION TEST
LDW
LDW : Description
INFOID:0000000011277216
• Perform action test to verify the customer's concern.
• Perform action test and check the system operation after system diagnosis.
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Fully understand the following items well before the road test;
- Precautions: Refer to
DAS-9, "Precautions for Driver Assistance Systems"
.
- System description for LDW: Refer to
DAS-15, "LDW : System Description"
- System description for BSW: Refer to
DAS-19, "BSW : System Description"
- System description for MOD: Refer to
DAS-25, "MOD : System Description"
- Handling precaution: Refer to
DAS-35, "Precautions for Lane Departure Warning"
.
LDW : Inspection Procedure
INFOID:0000000011277217
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Fully understand the following items well before the road test;
- Precautions: Refer to
DAS-9, "Precautions for Driver Assistance Systems"
.
- System description for LDW: Refer to
DAS-15, "LDW : System Description"
- System description for BSW: Refer to
DAS-19, "BSW : System Description"
- System description for MOD: Refer to
DAS-25, "MOD : System Description"
- Handling precaution: Refer to
DAS-35, "Precautions for Lane Departure Warning"
.
1.
CHECK LDW SYSTEM SETTING
1. Start the engine.
2. Check that the LDW system setting can be enabled/disabled on the vehicle information display.
3. Turn OFF the ignition switch and wait for 30 seconds or more.
4. Check that the previous setting is saved when the engine starts again.
>> GO TO 2.
2.
ACTION TEST FOR LDW
1. Enable the setting of the LDW system on the vehicle information display.
2. Turn warning systems switch ON (warning systems ON indicator is ON).
3. Check the LDW operation according to the following table.
DAS-80
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
ACTION TEST
NOTE:
After the operating conditions of warning are satisfied, the warning continues until the vehicle speed
reaches approximately 60 km/h (40 MPH). Refer to
DAS-15, "LDW : System Description"
>> Inspection End.
BSW
BSW : Description
INFOID:0000000011277218
• Perform action test to verify the customer's concern.
• Perform action test and check the system operation after system diagnosis.
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Fully understand the following items well before the road test;
- Precautions: Refer to
DAS-9, "Precautions for Driver Assistance Systems"
- System description for LDW: Refer to
DAS-19, "BSW : System Description"
- System description for BSW: Refer to
DAS-19, "BSW : System Description"
- System description for MOD: Refer to
DAS-25, "MOD : System Description"
.
- Handling precaution: Refer to
DAS-36, "Precautions for Blind Spot Warning"
BSW : Inspection Procedure
INFOID:0000000011277219
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Fully understand the following items well before the road test;
- Precautions: Refer to
DAS-9, "Precautions for Driver Assistance Systems"
- System description for LDW: Refer to
DAS-15, "LDW : System Description"
- System description for BSW: Refer to
DAS-19, "BSW : System Description"
- System description for MOD: Refer to
DAS-25, "MOD : System Description"
.
Vehicle condition/ Driver's operation
Action
Warning sys-
tems ON indi-
cator
Indication on the combination
meter
Buzzer
Less than
Approx. 60
km/h (40
MPH)
Close to lane marker
No action
ON
—
Approx. 70
km/h (45
MPH) or
more
Close to lane marker
Warning
• Buzzer sounds
• Warning lamp
blinks
ON
Short contin-
uous beeps
• Close to lane marker
• Turn signal ON (Deviate
side)
No action
ON
—
ALOIA0191GB
ALOIA0190GB
ALOIA0191GB
DAS
ACTION TEST
DAS-81
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
- Handling precaution: Refer to
DAS-36, "Precautions for Blind Spot Warning"
1.
CHECK BSW SYSTEM SETTING
1. Start the engine.
2. Check that the BSW system setting can be enabled/disabled on the vehicle information display.
3. Turn OFF the ignition switch and wait for 30 seconds or more.
4. Check that the previous setting is saved when the engine starts again.
>> GO TO 2.
2.
ACTION TEST FOR BSW
1. Enable the setting of the BSW system on the vehicle information display.
2. Turn warning systems switch ON (warning systems ON indicator is ON).
3. Check the BSW operation according to the following table.
Vehicle condition/Driver’s operation
NOTE:
After the operating conditions of warning are satisfied, the warning continues until the vehicle speed
reaches approximately 60 km/h (40 MPH). Refer to
DAS-19, "BSW : System Description"
.
>> Inspection End.
MOD
MOD : Description
INFOID:0000000011277220
• Perform action test to verify the customer's concern.
• Perform action test and check the system operation after system diagnosis.
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
Warning
systems
ON
indicator
Vehicle
speed (Ap-
prox.)
[km/h
(MPH)]
Turn signal con-
dition
Status of vehi-
cle detection
within detec-
tion area
Indication on the combination meter
Buzzer
ON
Less than
Approx. 29
km/h (18
MPH)
—
—
OFF
OFF
Approx. 32
km/h (20
MPH) or
more
—
Vehicle is ab-
sent
OFF
OFF
OFF
Vehicle is de-
tected
ON
OFF
ON (vehicle de-
tected direction)
Before turn
signal oper-
ates vehicle is
detected
Blink
Short continuous beeps
Vehicle is de-
tected after
turn signal op-
erates
Blink
OFF
JSOIA0251GB
JSOIA0252GB
JSOIA0251GB
DAS-82
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
ACTION TEST
• Fully understand the following items well before the road test;
- Precautions: Refer to
DAS-9, "Precautions for Driver Assistance Systems"
- System description for LDW: Refer to
DAS-15, "LDW : System Description"
- System description for BSW: Refer to
DAS-19, "BSW : System Description"
- System description for MOD: Refer to
DAS-25, "MOD : System Description"
.
- Handling precaution: Refer to
DAS-37, "Precautions for Moving Objects Detection"
.
MOD : Inspection Procedure
INFOID:0000000011277221
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Fully understand the following items well before the road test;
- Precautions: Refer to
DAS-9, "Precautions for Driver Assistance Systems"
- System description for LDW: Refer to
DAS-15, "LDW : System Description"
- System description for BSW: Refer to
DAS-19, "BSW : System Description"
- System description for MOD: Refer to
DAS-25, "MOD : System Description"
.
- Handling precaution: Refer to
DAS-37, "Precautions for Moving Objects Detection"
.
1.
CHECK MOD SYSTEM SETTING
1. Start the engine.
2. Check that the MOD system setting can be enabled/disabled on the vehicle information display.
3. Turn OFF the ignition switch and wait for 30 seconds or more.
4. Check that the previous setting is saved when the engine starts again.
>> GO TO 2.
2.
ACTION TEST FOR MOD
1. Enable the setting of the MOD system on the vehicle information display.
2. Turn warning systems switch ON (warning systems ON indicator is ON).
3. Check the MOD operation according to the following table.
NOTE:
After the operating conditions of warning are satisfied, the warning continues until the vehicle reaches a
higher speed. Refer to
DAS-25, "MOD : System Description"
.
>> Inspection End.
FCW
FCW : Description
INFOID:0000000011505728
• Perform action test to verify the customer's concern.
• Perform action test and check the system operation after system diagnosis.
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
• Fully understand the following items well before the road test;
- Precautions: Refer to
DAS-9, "Precautions for Driver Assistance Systems"
Vehicle condition/ Driver's operation
Vehicle response
Moving Object De-
tection ON indicator
Vehicle speed
(Approx.)
[km/h (MPH)]
Status of vehicle detection
within detection area
Indication on the Moving Object Detection
indicator
Buzzer
OFF
—
—
OFF
OFF
Blue
Less than approx.
8 km/h (5 MPH)
Vehicle is detected
ON
ON
Approx. 8 km/h (5
MPH) or more
Vehicle is absent
ON
OFF
Vehicle is detected
ON
OFF
Vehicle is not detected
ON
OFF
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст