Nissan Rogue. Manual — part 1124
SRC-46
< DTC/CIRCUIT DIAGNOSIS >
B0001, B0002 DRIVER AIRBAG MODULE
Is the DTC detected?
YES
>> Refer to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011279544
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
HARNESS CONNECTOR
Visually inspect all applicable harness connectors for the following:
• Visible damage to connector or terminal
• Loose terminal
• Poor connection
NOTE:
All harness connectors should be inspected from the air bag diagnosis sensor unit to the end component
(including any in-line connectors).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Perform one of the following repairs:
• Visible damage: Replace the harness.
• Loose terminal: Secure the terminal.
• Poor connection: Secure the connection.
2.
CONFIRM DTC
1. Reconnect all harness connectors.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 3.
NO
>> Refer to
GI-44, "Intermittent Incident"
.
3.
WIRING HARNESS
Check the wiring harness for visible damage.
NOTE:
The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component
(including any in-line connectors).
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace the harness.
4.
CHECK SPIRAL CABLE CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver air bag module harness connector and combination switch (spiral cable) harness con-
nector.
3. Check continuity between driver air bag module harness connector and combination switch (spiral cable)
harness connector.
4. Check continuity between driver air bag module harness connector and ground.
Driver air bag module
Combination switch (spiral cable)
Continuity
Connector
Terminal
Connector
Terminal
B92
29
M53
4
Yes
30
3
B93
32
2
31
3
B0001, B0002 DRIVER AIRBAG MODULE
SRC-47
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace combination switch (spiral cable). Refer to
SR-15, "Removal and Installation"
.
5.
CONFIRM DTC
1. Reconnect all harness connectors.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 6.
NO
>> Refer to
GI-44, "Intermittent Incident"
.
6.
AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace the air bag diagnosis sensor unit. Refer to
SR-26, "Removal and Installation"
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 7.
NO
>> Clear DTC. Inspection End.
7.
DRIVER AIR BAG MODULE
1. Replace the driver air bag module. Refer to
SR-12, "Removal and Installation"
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 8.
NO
>> Clear DTC. Inspection End.
8.
RELATED HARNESS
Replace the related harness.
>> END
Driver side air bag module
Ground
Continuity
Connector
Terminal
B92
29
No
30
B93
32
31
SRC-48
< DTC/CIRCUIT DIAGNOSIS >
B0010, B0011 PASSENGER AIRBAG MODULE
B0010, B0011 PASSENGER AIRBAG MODULE
DTC Logic
INFOID:0000000011279545
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE (With CONSULT)
1.
CHECK SELF DIAGNOSTIC RESULT
1. Turn ignition switch ON.
2. Check for DTC using CONSULT.
Is the DTC detected?
YES (Current DTC)>>Refer to
YES (Past DTC)>>GO TO 2.
NO
>> Inspection End.
2.
ERASE SELF DIAGNOSTIC RESULT
Erase the DTC using CONSULT.
Can the DTC be erased?
YES
>> Inspection End.
NO
>> Refer to
DTC CONFIRMATION PROCEDURE (Without CONSULT)
1.
CHECK SELF DIAGNOSTIC RESULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to
SRC-14, "On Board Diagnosis Function"
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
Is the DTC detected?
YES
>> Refer to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011279546
1.
HARNESS CONNECTOR
Visually inspect all applicable harness connectors for the following:
CONSULT name
DTC
DTC detecting condition
Repair order
ASSIST AIRBAG MODULE CIRCUIT
[OPEN]
B0010
Front passenger air bag module circuit
(AS1) is open.
Refer to
.
ASSIST AIRBAG MODULE CIRCUIT
[VB-SHORT]
Front passenger air bag module circuit
(AS1) is shorted to a power supply cir-
cuit.
ASSIST AIRBAG MODULE CIRCUIT
[GND-SHORT]
Front passenger air bag module circuit
(AS1) is shorted to ground.
ASSIST AIRBAG MODULE CIRCUIT
[SHORT]
Front passenger air bag module cir-
cuits (AS1) are shorted to each other.
ASSIST AIRBAG MODULE 2ND CIRCUIT
[OPEN]
B0011
Front passenger air bag module circuit
(AS2) is open.
ASSIST AIRBAG MODULE 2ND CIRCUIT
[VB-SHORT]
Front passenger air bag module circuit
(AS2) is shorted to a power supply cir-
cuit.
ASSIST AIRBAG MODULE 2ND CIRCUIT
[GND-SHORT]
Front passenger air bag module circuit
(AS2) is shorted to ground.
ASSIST AIRBAG MODULE 2ND CIRCUIT
[SHORT]
Front passenger air bag module cir-
cuits (AS2) are shorted to each other.
B0010, B0011 PASSENGER AIRBAG MODULE
SRC-49
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
• Visible damage to connector or terminal
• Loose terminal
• Poor connection
NOTE:
All harness connectors should be inspected from the air bag diagnosis sensor unit to the end component
(including any in-line connectors).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Perform one of the following repairs:
• Visible damage: Replace the harness.
• Loose terminal: Secure the terminal.
• Poor connection: Secure the connection.
2.
CONFIRM DTC
1. Reconnect all harness connectors.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 3.
NO
>> Refer to
GI-44, "Intermittent Incident"
.
3.
WIRING HARNESS
Check the wiring harness for visible damage.
NOTE:
The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component
(including any in-line connectors).
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace the harness.
4.
CONFIRM DTC
1. Reconnect all harness connectors.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 5.
NO
>> Refer to
GI-44, "Intermittent Incident"
.
5.
AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace the air bag diagnosis sensor unit. Refer to
SR-26, "Removal and Installation"
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 6.
NO
>> Clear DTC. Inspection End.
6.
FRONT PASSENGER AIR BAG MODULE
1. Replace the front passenger air bag module. Refer to
SR-17, "Removal and Installation"
.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 7.
NO
>> Clear DTC. Inspection End.
7.
RELATED HARNESS
Replace the related harness.
>> END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст