Nissan Rogue. Manual — part 1233
WT-8
< SYSTEM DESCRIPTION >
COMPONENT PARTS
Tire Pressure Sensor
INFOID:0000000011280489
The tire pressure sensor (1) integrated with the valve is installed in
each wheel (2), and transmits the detected tire pressure and temper-
ature signal in the form of the radio wave. The radio signal is
received by the BCM (tire pressure receiver).
: Outside
JSEIA0747ZZ
SYSTEM
WT-9
< SYSTEM DESCRIPTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
SYSTEM
System Description
INFOID:0000000011280490
• During driving, the TPMS (Tire Pressure Monitoring System) receives the signal transmitted from tire pres-
sure sensor installed in each wheel. The BCM of this system has pressure judgment and trouble diagnosis
functions. When the TPMS (Tire Pressure Monitoring System) detects low inflation pressure or another
unusual symptom, the low tire pressure warning lamp in the combination meter comes on.
• Tire pressure varies as per the change in tire temperature. There-
fore, warning tire pressure value is varied as per the change in tire
temperature.
• If the tire pressure is less than the warning tire pressure value, the
low tire pressure warning lamp illuminates.
• Location of wheel is specified due to the synchronism of wheel sensor position and tire pressure sensor
position.
• Activates the TPMS (Tire Pressure Monitoring System) when the vehicle speed is 40 km/h (25 MPH) or
more.
• The tire pressure monitoring system (TPMS) has Easy Fill Tire alert function to aid in tire inflation. Refer to
WT-11, "Easy Fill Tire Alert Function"
.
SYSTEM DIAGRAM
INPUT/OUTPUT SIGNAL
Major signal transmission between each unit via communication lines is shown in the following table.
JMEIA0240GB
ALEIA0195GB
WT-10
< SYSTEM DESCRIPTION >
SYSTEM
LOW TIRE PRESSURE WARNING LAMP INDICATION CONDITION
Uses CAN communication from the BCM to illuminate the low tire pressure warning lamp on the combination
meter.
LOW TIRE PRESSURE LOCATION INDICATOR
The low tire pressure location indicator is displayed in the information display of combination meter with the
low tire pressure warning lamp and warning message under the following conditions:
• Tire pressure is low.
• Tire goes flat.
Component parts
Signal item
BCM
Mainly transmits the following signals to combination meter via CAN communication.
• Low tire pressure warning lamp signal
• Low tire pressure wheel location signal
• TPMS malfunction warning lamp signal
Mainly receives the following signal from ABS actuator and electric unit (control unit) via CAN
communication.
• Vehicle speed signal (ABS)
Combination meter
Mainly receives the following signals from BCM via CAN communication.
• Low tire pressure warning lamp signal
• Low tire pressure wheel location signal
• TPMS malfunction warning lamp signal
ABS actuator and electric unit (con-
trol unit)
Mainly transmits the following signal to BCM via CAN communication:
• Vehicle speed signal (ABS)
TCM
Mainly transmits the following signal to BCM via CAN communication:
• Shift position signal (P range signal)
IPDM E/R
Mainly receives the following signal from BCM via CAN communication:
• Horn reminder signal
Name
Design
Layout
Low tire pressure warning lamp
Refer to
MWI-7, "METER SYSTEM : Design"
Condition
Low tire pressure warning lamp
Ignition switch OFF
OFF
Ignition switch ON
(System normal)
Warning lamp turns on for 1 second, then turns off.
Low tire pressure
ON
Configuration not performed in tire pressure monitoring system
Warning lamp blinks 1 min., then turns on.
Tire pressure sensor ID not registered in BCM
Tire pressure monitoring system malfunction
(Other diagnostic item)
SYSTEM
WT-11
< SYSTEM DESCRIPTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
TIRE PRESSURE DISPLAY
The adoption of this function allows tire pressure indication on the information display installed to the combina-
tion meter.
HAZARD WARNING LAMP INDICATION CONDITION
The hazard warning lamp blinks under the following conditions:
• When ID registration is completed. Refer to
• During the use of the Easy Fill Tire Alert function.
HORN CONTROL CONDITION
During the use of Easy Fill Tire Alert function.
Easy Fill Tire Alert Function
INFOID:0000000011280491
• This function operates only when the select lever position is in P-range with the ignition switch ON.
NOTE:
The Easy Fill tire alert function is recommended to use with the ignition switch ON.
NOTE:
When beginning tire inflation, it takes a few seconds for the Easy fill tire alert to function. If there is no
response for approximately 15 seconds or more, cancel the Easy fill tire alert function and move the vehicle
approximately 1 m (3.2 ft) backward or forward to try again.
• The Easy fill tire alert function operates only when the select lever position is in P-range with the ignition
switch ON.
• This function informs the driver with a visual and audible indication that the recommended COLD tire pres-
sure has been reached.
Design
Massage
Tire Pressure Low Add Air
JMEIA0247ZZ
Design
Description
• Tire pressure of each tire is displayed at side of each tire.
• Setting tire pressure of front and rear tires are displayed between front/rear
tires.
JMEIA0248ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст