Nissan Rogue. Manual — part 1159

TM-8

< PRECAUTION >

[CVT: RE0F10D]

PRECAUTIONS

CAUTION:

• Be sure to turn the ignition switch OFF and disconnect the battery cable from the negative terminal

before any repair or inspection work. The open/short circuit of related switches, sensors, solenoid

valves, etc. will cause the MIL to light up.

• Be sure to connect and lock the connectors securely after work. A loose (unlocked) connector will

cause the MIL to light up due to an open circuit. (Be sure the connector is free from water, grease,

dirt, bent terminals, etc.)

• Be sure to route and secure the harnesses properly after work. Interference of the harness with a

bracket, etc. may cause the MIL to light up due to a short circuit.

• Be sure to connect rubber tubes properly after work. A misconnected or disconnected rubber tube

may cause the MIL to light up due to a malfunction of the EGR system or fuel injection system, etc.

• Be sure to erase the unnecessary malfunction information (repairs completed) from the TCM and

ECM before returning the vehicle to the customer.

Removal and Installation Procedure for CVT Unit Connector

INFOID:0000000011279242

REMOVAL

• Rotate bayonet ring counterclockwise. Pull out CVT unit har-

ness connector upward and remove it.

INSTALLATION

1. Align marking on CVT unit harness connector terminal with

marking on bayonet ring. Insert CVT unit harness connector.

2. Rotate bayonet ring clockwise.

3. Rotate bayonet ring clockwise until marking on CVT unit har-

ness connector terminal body is aligned with the slit on bayo-

net ring as shown in the figure (correctly fitting condition).

CAUTION:

SCIA6685J

JPDIA0294ZZ

JPDIA0295ZZ

PRECAUTIONS

TM-9

< PRECAUTION >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

• Securely align marking on CVT unit harness connector

terminal body with bayonet ring slit . Then, be careful

not to make a half fit condition as shown in the figure.

• Never mistake the slit of bayonet ring for other dent por-

tion.

JPDIA0296ZZ

TM-10

< PREPARATION >

[CVT: RE0F10D]

PREPARATION

PREPARATION

PREPARATION

Special Service Tools

INFOID:0000000011279243

The actual shape of the tools may differ from those illustrated here.

*: The O-ring as a unit part is set as a SST.

Commercial Service Tools

INFOID:0000000011279244

Tool number
(TechMate No.)
Tool name

Description

1.

KV311039S0
(

—

)

Charging pipe set

2.

KV31103920*
(

—

)

O-ring

CVT fluid changing and adjustment

KV38107900
(

—

)

Protector
a: 32 mm (1.26 in) dia.

Installing drive shaft

JSDIA1844ZZ

PDIA1183J

Tool number
Tool name

Description

Power tool

Loosening nuts, screws and bolts

Lint-free paper

Cleaning transaxle

PIIB1407E

JSDIA4746ZZ

PREPARATION

TM-11

< PREPARATION >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Drift
a: 53 mm (2.09 in) dia.
b: 50 mm (1.97 in) dia.

Installing differential side oil seal

Drift
a: 65 mm (2.56 in) dia.
b: 60 mm (2.36 in) dia.

Installing converter housing oil seal

Tool number
Tool name

Description

NT115

NT115