Nissan Rogue. Manual — part 13
AV-44
< BASIC INSPECTION >
[DISPLAY AUDIO]
DIAGNOSIS AND REPAIR WORKFLOW
Is malfunctioning part detected?
YES
>> GO TO 4.
NO
>> GO TO 2.
4.
REPAIR OR REPLACE THE MALFUNCTIONING PART
1. Repair or replace the malfunctioning part.
2. Reconnect parts or connectors disconnected during Diagnostic Procedure.
>> GO TO 5.
5.
FINAL CHECK
Refer to confirmed symptom in step 2, and make sure that the symptom is not detected.
Was the repair confirmed?
YES
>> Inspection End.
NO
>> GO TO 2.
AV
INSPECTION AND ADJUSTMENT
AV-45
< BASIC INSPECTION >
[DISPLAY AUDIO]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
INSPECTION AND ADJUSTMENT
REGISTRATION (AUDIO UNIT)
REGISTRATION (AUDIO UNIT) : Description
INFOID:0000000011276747
AFTER REPLACEMENT
If the audio unit is replaced with a new audio unit, the new audio unit must be registered using the Bluetooth D/
C(serial #).
CAUTION:
If the new audio unit Bluetooth D/C(serial #) is not registered, the “APPS” mode will not function.
REGISTRATION (AUDIO UNIT) : Work Procedure
INFOID:0000000011276748
1.
RECORD BLUETOOTH D/C(SERIAL #) FOR REPLACEMENT AUDIO UNIT
1. Turn ignition switch ON.
2. Turn audio unit OFF.
3. Access the diagnostic menu as follows:
-
Press and hold preset buttons 2 and 3.
-
While holding preset buttons 2 and 3, press preset button 5
three times.
4. Select Version Information from the Diagnostic Menu.
AWNIA3612ZZ
AWNIA3613ZZ
ALNIA1652ZZ
AV-46
< BASIC INSPECTION >
[DISPLAY AUDIO]
INSPECTION AND ADJUSTMENT
5. Scroll through the menu pages to Bluetooth D/C(serial #) and
record the number displayed.
>> GO TO 2.
2.
REGISTER REPLACEMENT AUDIO UNIT
Register the replacement audio unit by contacting NISSAN Owner Services. Refer to TSB.
>> GO TO 3.
3.
OPERATION CHECK
Verify that the audio unit “APPS” function operates normally.
>> Work End.
ALNIA1653ZZ
AV
POWER SUPPLY AND GROUND CIRCUIT
AV-47
< DTC/CIRCUIT DIAGNOSIS >
[DISPLAY AUDIO]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
DTC/CIRCUIT DIAGNOSIS
POWER SUPPLY AND GROUND CIRCUIT
AUDIO UNIT
AUDIO UNIT : Diagnosis Procedure
INFOID:0000000011276749
Regarding Wiring Diagram information, refer to
1.
CHECK FUSE
Check that the following fuses are not blown:
Are the fuses blown?
YES
>> Replace the blown fuse after repairing the affected circuit.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect audio unit connector M83.
3. Check voltage between audio unit connector M83 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connectors.
3.
CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect audio unit connector M87.
3. Check continuity between audio unit connectors and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair or replace harness or connectors.
Terminal No.
Signal name
Fuse No.
7
Ignition power supply
30 (10A)
19
Battery power supply
16 (20A)
Audio unit
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
M83
7
—
Ignition switch: ON
Battery voltage
19
Ignition switch: OFF
Audio unit
Ground
Continuity
Connector
Terminal
M83
20
—
Yes
M87
52
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст