Nissan Rogue. Manual — part 146
BR-54
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT DISC BRAKE
4. Apply brake fluid to each piston (1). Push each piston into cylin-
der body by hand and push piston boot (2) piston-side lip into
the piston groove.
CAUTION:
Press the piston evenly and vary the pressing point to pre-
vent cylinder inner wall from being rubbed.
5. Apply Niglube Rx-2 grease to bushing; install bushing to slide pin.
6. Apply Niglube Rx-2 grease to slide pins and slide pin boots, install slide pins and slide pin boots to torque
member.
7. Install the brake caliper to the vehicle. Refer to
BR-42, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE)
.
INSPECTION AFTER INSTALLATION
1. Check the drag of front disc brake. If any drag is found, follow the procedure described below.
2. Remove brake pads.
3. Using a suitable tool, press the pistons into the brake caliper body.
CAUTION:
Do not damage the piston boots.
4. Install brake pads.
5. Depress the brake pedal several times.
6. Check the drag of front disc brake again. If any drag is found, disassemble the brake caliper body.
7. Burnish contact surfaces after refinishing or replacing disc brake rotors or if a soft pedal occurs at very low
mileage. Refer to
JPFIA0034ZZ
REAR DISC BRAKE
BR-55
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
REAR DISC BRAKE
Exploded View
INFOID:0000000011279903
Disassembly and Assembly
INFOID:0000000011279904
DISASSEMBLY
1. Remove the brake caliper from the vehicle. Refer to
BR-47, "BRAKE CALIPER ASSEMBLY : Removal
2. Remove slide pin boots from torque member.
3. Remove slide pin bolt bushing from slide pin bolt.
4. Place a wooden block in the cylinder body and blow air from
union bolt hole to remove piston and piston boot.
WARNING:
Do not get fingers caught between pistons and brake cali-
per body.
CAUTION:
Do not reuse piston boot.
1.
Slide pin bolt
2.
Slide pin bolt bushing
3.
Cap
4.
Bleeder valve
5.
Brake caliper body
6.
Piston seal
7.
Piston
8.
Piston boot
9.
Slide pin boot
10. Torque member
A.
Niglube Rx-2
B.
Rubber grease
Apply brake fluid
AWFIA1116ZZ
BRD0041D
BR-56
< UNIT DISASSEMBLY AND ASSEMBLY >
REAR DISC BRAKE
5. Remove piston seal from brake caliper body using suitable tool.
CAUTION:
• Do not damage cylinder inner wall.
• Do not reuse piston seal.
6. Remove bleeder valve and cap.
INSPECTION AFTER DISASSEMBLY
Brake Caliper Body
Check the inner wall of the brake caliper body for rust, wear, cracks or damage. Replace the brake caliper if
any abnormal condition is detected.
CAUTION:
Always clean with new brake fluid. Do not clean with mineral oil such as gasoline and light oil.
Torque Member
Check the torque member for rust, wear, cracks or damage. Replace the brake caliper if any abnormal condi-
tion is detected.
Piston
Check the surface of the piston for rust, wear, cracks or damage. Replace the brake caliper if any abnormal
condition is detected.
CAUTION:
Piston sliding surface is plated. Do not polish with sandpaper.
Slide Pin and Slide Pin Bolt Boot
Check the slide pins and slide pin bolt boots for rust, wear, cracks or damage. Replace the parts if any abnor-
mal condition is detected.
ASSEMBLY
1. Install bleeder valve and cap.
2. Apply rubber grease to piston seal (1), and install it to the brake
caliper body.
CAUTION:
Do not reuse piston seal.
3. Apply rubber grease to piston boot (1). Cover the piston end (2)
with the piston boot (1), and then install cylinder side lip on the
piston boot securely into the groove on brake caliper body.
CAUTION:
Do not reuse piston boot.
JPFIA0038ZZ
JPFIA0039ZZ
JPFIA0040ZZ
REAR DISC BRAKE
BR-57
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
4. Apply brake fluid to piston (1). Push piston into brake caliper
body by hand and push piston boot (2) piston side lip into the
piston groove.
CAUTION:
Press the piston evenly and vary the pressing point to pre-
vent cylinder inner wall from contact.
5. Apply Niglube Rx-2 grease to bushing; install bushing to slide pin bolt.
6. Install slide pin boots to torque member.
7. Install the brake caliper to the vehicle. Refer to
BR-47, "BRAKE CALIPER ASSEMBLY : Removal and
.
INSPECTION AFTER INSTALLATION
1. Check the drag of rear disc brake. If any drag is found, follow the procedure described below.
2. Remove brake pads.
3. Using a suitable tool, press the pistons into the brake caliper body.
CAUTION:
Do not damage the piston boots.
4. Install brake pads.
5. Depress the brake pedal several times.
6. Check the drag of rear disc brake again. If any drag is found, disassemble the brake caliper body.
7. Burnish contact surfaces after refinishing or replacing disc brake rotors or if a soft pedal occurs at very low
mileage. Refer to
JPFIA0041ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст