Nissan Rogue. Manual — part 592
PREPARATION
EX-3
< PREPARATION >
C
D
E
F
G
H
I
J
K
L
M
A
EX
N
P
O
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000011279724
The actual shape of the tools may differ from those illustrated here.
Commercial Service Tools
INFOID:0000000011279725
Tool number
(TechMate No.)
Tool name
Description
—
(J-43897-18)
Oxygen sensor thread cutter
Reconditioning the exhaust system threads
before installing a new oxygen sensor (Use
with anti-seize lubricant)
M18 x 1.5 threads
KV10114400
(J-38365)
Heated oxygen sensor wrench
Loosening or tightening heated oxygen sen-
sors:
a: 22 mm (0.87 in)
AWBIA1764ZZ
S-NT636
Tool name
Description
Power tool
Loosening nuts, screws and bolts
Heated oxygen sensor wrench
Loosening or tightening heated oxygen sen-
sor
For 22 mm (0.87 in) hexagon nut
Anti-seize lubricant (Permatex 133AR
or equivalent meeting MIL specifica-
tion MIL-A-907)
Lubricating oxygen sensor thread cleaning
tool when reconditioning exhaust system
threads
PIIB1407E
NT379
AEM489
EX-4
< PERIODIC MAINTENANCE >
EXHAUST SYSTEM
PERIODIC MAINTENANCE
EXHAUST SYSTEM
Inspection
INFOID:0000000011279726
Check exhaust pipes, muffler, and mounting for improper attach-
ment, leakage, cracks, damage or deterioration.
• If anything is found, repair or replace damaged parts.
SMA211A
EXHAUST SYSTEM
EX-5
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EX
N
P
O
REMOVAL AND INSTALLATION
EXHAUST SYSTEM
Exploded View
INFOID:0000000011279727
Removal and Installation
INFOID:0000000011279728
WARNING:
• Perform the procedures with the exhaust system fully cooled down to avoid injury from the hot
exhaust system.
• Be careful not to cut your hand on the catalyst shroud edge.
CAUTION:
Use genuine NISSAN exhaust system parts or equivalent, which are specifically designed for heat
resistance, corrosion resistance, and shape.
1.
Exhaust diffuser
2.
Muffler assembly
3.
Mounting rubber
4.
Mounting rubber
5.
Mounting rubber
6.
Ring gasket
7.
Front exhaust tube
8.
Mounting rubber
9.
Exhaust gasket
10. Oxygen sensor 2
11. Center exhaust tube
12. Catalyst shroud
A.
To exhaust manifold and three way
catalyst
AWBIA2279ZZ
EX-6
< REMOVAL AND INSTALLATION >
EXHAUST SYSTEM
REMOVAL
1. Remove exhaust system components using power tool.
2. Remove heated oxygen sensor 2 using suitable tool or Tool.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse exhaust gasket.
• Do not reuse nuts securing front exhaust tube to exhaust manifold and three way catalyst.
• Do not allow foreign substances to contact new exhaust gasket.
• Be sure to install ring gasket to prevent catching when tightening.
• Do not reuse ring gasket.
• Ensure flexible portion of front exhaust tube is free from deformation.
• During installation, take care not to deform mounting rubbers. After installing, the mounting rubbers
shall show no excessive movement, twisting, or elongation. To facilitate installation, a neutral deter-
gent may be used.
• Mounting rubbers installed at either side of muffler are to be installed in accordance with paint
marks. Mounting rubber at LH side is installed with white paint mark facing forward. Mounting rub-
ber at RH side is installed with white paint mark facing rearward.
• Apply anti-seize lubricant to heated oxygen sensor 2 before installing.
• Do not spray exhaust tubes, muffler, heated oxygen sensor 2, or catalyst shroud with anti-corrosive
wax.
• If catalyst shroud is badly deformed, repair or replace it. If deposits, such as mud, pile up on the cat-
alyst shroud, remove them.
• When installing catalyst shroud, avoid large gaps or interference between catalyst shroud and
exhaust pipe.
• Temporarily tighten fasteners and check each part for interference with other components, and then
tighten fasteners to specification.
• Discard any heated oxygen sensor 2 which has been dropped.
• Before installing a new heated oxygen sensor 2, clean exhaust system threads using Tool.
• Tighten heated oxygen sensor 2 using suitable tool. Do not use impact wrench.
• Do not over tighten heated oxygen sensor 2. Doing so may cause damage to the heated oxygen sen-
sor 2, resulting in the “MIL” coming on.
• Remove deposits from the sealing surface of each connection. Connect them securely to avoid
exhaust gas leaks.
Inspection
INFOID:0000000011279729
INSPECTION AFTER INSTALLATION
• Check clearance between tail tube and rear bumper is even.
• With engine running, check exhaust tube joints for gas leakage and unusual noises.
• Check to ensure that mounting brackets and mounting rubbers are installed properly and free from undue
stress. Improper installation could result in excessive noise and vibration.
Tool number
: KV10114400 (J-38365)
Tool number
: — (J-43897-18)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст