Nissan Rogue. Manual — part 814
BODY SIDE TRIM
INT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
2. Release the front pillar finisher pawls using a suitable tool.
: Pawl
3. Cut and discard front pillar finisher tether clip (A).
CAUTION:
Do not reuse tether clip. Replace with new part after
removal.
4. Remove the remaining piece of tether clips (A) using a suitable
tool and remove front pillar finisher.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse tether clip. Replace with new part for installation.
• Make sure that the location of the airbag and tether clip do not block body panel holes before install-
ing front pillar finisher.
• Make sure to install tether clip to front pillar finisher by inserting clip end and rotating 90 degrees in
either direction, before installing front pillar finisher.
• When installing tether clip to front pillar finisher, be sure to
install by aligning to the cutout.
• Front pillar finisher is re-usable.
• New tether clip should be used from service parts, ordered
separately.
• When installing front pillar finisher, check that tether clip and pawls are securely placed into correct
body panel holes.
CENTER PILLAR UPPER FINISHER
CENTER PILLAR UPPER FINISHER : Removal and Installation
INFOID:0000000011277478
REMOVAL
1. Remove center pillar lower finisher. Refer to
INT-22, "CENTER PILLAR LOWER FINISHER : Removal
ALJIA1342ZZ
JMJIA7045ZZ
INT-22
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
2. Release pawls, using a suitable tool and remove the seat belt
height adjuster finisher (1).
: Pawl
3. Remove front D-ring anchor bolt.
CAUTION:
Before removing D-ring anchor bolt note the positions of washers and spacers for correct installa-
tion.
4. Release center pillar upper finisher clips using a suitable tool as shown.
5. Release center pillar upper finisher (1) clips using a suitable tool
and remove.
: Clip
CAUTION:
• Do not reuse center pillar upper finisher.
• Do not bend the sheet metal when removing the center pillar upper finisher from the sheet metal.
• When releasing molded in clip, follow the steps as shown to prevent finisher or clip damage.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse center pillar upper finisher. Replace with new part for installation.
• Visually check sheet metal around clip and pawl locations to confirm no deformation from removal
of center pillar upper finisher. Repair sheet metal if necessary.
• When installing center pillar upper finisher, check that the clips are securely placed in body panel
holes.
CENTER PILLAR LOWER FINISHER
CENTER PILLAR LOWER FINISHER : Removal and Installation
INFOID:0000000011277479
REMOVAL
1. Move front seat to the full forward position.
AWHIA0539ZZ
ALJIA1346ZZ
PIIB2600J
BODY SIDE TRIM
INT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
2. Remove front kicking plate. Refer to
INT-23, "KICKING PLATE : Removal and Installation - Front Kicking
.
3. Partially remove the front door welt.
4. Remove rear kicking plate. Refer to
INT-24, "KICKING PLATE : Removal and Installation - Rear Kicking
.
5. Partially remove the rear door welt.
6. Release center pillar lower finisher clips and pawls using a suit-
able tool, then remove the center pillar lower finisher (1).
: Clip
: Pawl
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips for deformation and damage during installation. Replace with new ones if
necessary.
• When installing center pillar lower finisher, check that clips and pawls are securely placed in body
panel holes.
BODY SIDE WELT
BODY SIDE WELT : Removal and Installation - Front Door Welt
INFOID:0000000011277480
REMOVAL
1. Remove the front kicking plate. Refer to
INT-23, "KICKING PLATE : Removal and Installation - Front Kick-
2. Remove the front body side welt.
INSTALLATION
Installation is in the reverse order of removal.
BODY SIDE WELT : Removal and Installation - Rear Door Welt
INFOID:0000000011277481
REMOVAL
1. Remove the rear kicking plate. Refer to
INT-24, "KICKING PLATE : Removal and Installation - Rear Kick-
2. Remove the rear body side welt.
INSTALLATION
Installation is in the reverse order of removal.
KICKING PLATE
KICKING PLATE : Removal and Installation - Front Kicking Plate
INFOID:0000000011277482
REMOVAL
AWJIA1282ZZ
INT-24
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
1. Release the front and rear pawls by rotating the front kicking
plate.
: Pawl
: Front
2. Lift front edge of front kicking plate and release the remaining
pawls using suitable tool (A) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips and pawls for deformation and damage during installation. Replace with new
ones if necessary.
• When installing front kicking plate, check that the floor trim does not cover harness protector slots.
• When installing front kicking plate, check that the clips and pawls are securely placed in body panel
holes.
KICKING PLATE : Removal and Installation - Rear Kicking Plate
INFOID:0000000011277483
REMOVAL
1. Release front inside pawl of rear kicking plate as shown, then lift
front end of rear kicking plate to release pawls and remove.
: Pawl
: Front
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips and pawls for deformation and damage during installation. Replace with new
ones if necessary.
• When installing rear kicking plate, check that the clips and pawls are securely placed in body panel
holes.
DASH SIDE FINISHER
DASH SIDE FINISHER : Removal and Installation
INFOID:0000000011277484
REMOVAL
1. Remove front kicking plate. Refer to
INT-23, "KICKING PLATE : Removal and Installation - Front Kicking
.
2. Partially remove the front door welt.
AWJIA1286ZZ
ALJIA1381ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст